These are the most commonly replaced parts in Fender® Blues Junior models from 1995 through the present.

Photo

Description

Price Purchase

Click on photo for
larger view
FENDER COMPLETE POTENTIOMETER KIT - BLUES JUNIOR.  Contains all 6 control pots as found in the Blues Junior and Blues Junior III (all versions) from 1993 to the present.
Part #FPK-116
$39.95  


Click on photo for
larger view
POT - SNAP-IN, 25K LINEAR, Used in the Blues Junior as the middle control. Fender® Part numbers  0049402000 AND 0049621000.

Part #FPBJ-25KL
$6.95  


Click on photo for
larger view
POT - SNAP-IN, 50K LINEAR, Used in the Blues Junior as the reverb control and the master volume. Fender® Part numbers  006268000 and 00347190000.

Part #FPBJ-50KL
$6.95  


Click on photo for
larger view
POT - SNAP-IN, 250K AUDIO, Used in the Blues Junior as the treble control. Fender® Part numbers 0041913000 AND 0049622000.

Part #FPBJ-250KA
$6.95  


Click on photo for
larger view
POT - SNAP-IN, 250K LINEAR, Used in the Blues Junior as the bass control. Fender® Part number 0040985000.

Part #FPBJ-250KL
$6.95  


Click on photo for
larger view
POT - SNAP-IN, 1MEG AUDIO, Used in the Blues Junior as the volume control. Fender® Part number 0049401000.

Part #FPBJ-1MA
$6.95  


Click on photo for
larger view
KNOB KIT, Fender®, Black with Pointer with bushing.   Replacement for Fender® Blues Junior.  Upgrade knob for original Blues Junior, Bronco, and Pro Junior.  Includes the Fender® style 36620000 Black Chicken-Head knob and the 0033206049 bushing.  Knob is a 1/4" set-screw type.  This combination replaces the original 041710 push-on knob used on the original Blues Junior - the 041710 knob is now discontinued.
Part #K-710
$2.95  


Click on photo for
larger view
KNOB, Fender® Style Chicken Head, 1/4" Set Screw, Cream.   Used on certain versions of the  Blues Junior III series.   Fender® part number 0058164049.   Fits 1/4" shaft, brass insert, with set screw.   
Part #K-640F
$1.95  


Click on photo for
larger view
BUSHING, Fender®, for push-on knobs   This bushing slides over the pot shaft before the knob is installed, and stabilizes the shaft as well as keeping the knob from rubbing the front faceplate.  The tapered end of the bushing fits into the hole in the faceplate.  The knob is inserted after the bushing is in place, and hides the bushing from view.  Original Fender® part number 0033206049.   Used on later versions of the Blues Junior, and also the early version if a set-screw chicken head knob is used to replace the discontinued push-on chicken head knobs.
Part #K-6049
$1.00  


Click on photo for
larger view

Note:  Nut & Washer NOT included - reuse original, or order JN-916.

JACK, 1/4", TIP/SLEEVE 4 PIN, PC MOUNT, Fender®, Blues Junior.
Fender
® PC mount 1/4" jack. Mono, 4 pin.  Used as the input jack on the Blues Junior.  
NUT & WASHER NOT INCLUDED - Reuse original nut and washer, or order JN-916.
Part # J-506

$1.99
 

 
Click on photo for
larger view
JACK, 1/4", MONO, CLOSED CIRCUIT MONO, PC MOUNT, Switchcraft® STYLE, NON-ISOLATED
Common PC mount input jack.   3 pins, mono, tip shunt. Shield tied to chassis mount.   Used in many amplifiers.   Fender® part number 030771.   Nut and washer included.

Part #J-112APC
$3.99  

 
Click on photo for
larger view
JACK, 1/4", MONO, CLOSED CIRCUIT MONO, PC MOUNT, Switchcraft® STYLE, ISOLATED NYLON BUSHING
Found in many applications.     3 pins, mono, tip shunt. Isolated sleeve.  Used as the 'Fat' footswitch jack in the Blues Junior.   Fender® part number 0027674000.  Nut and washer included.

Part #J-N112APC
$3.99  

NUT AND WASHER, CHROME, KOBICONN OR JALCO TYPE.
Fits J-506, J-506A, J-507, J-530, J-531, J-532, J-532G, J-533, J-533G, J-539, J-539G, J-540, J-545, J-6074, J-6075, J-560  
Part #JN-916

$0.79


Click on photo for
larger view
SAVE WITH MULTIPACK!  JNUT-38 JACK NUT AND WASHER, METAL, SWITCHCRAFT®, SET OF 6
Genuine Switchcraft® nut and washer set for the blackface/silverface Fender® bias pot, Mesa Boogie pots, and the CTS or Alpha pots with 3/8" bushing (found on original vintage Fender® blackface and silverface), as well as Peavey® and Switchcraft® 1/4" jacks.  Does NOT fit the 24mm Marshall® pots.   Set of 6 washers and 6 nuts. 
Part #JNUT-38-6
$3.99
(Set of 6 washers and 6 nuts)
 

JACK NUT AND WASHER, METAL, SWITCHCRAFT®
Genuine Switchcraft® nut and washer set for the blackface/silverface Fender® bias pot, Mesa Boogie pots, and the CTS or Alpha pots with 3/8" bushing (found on original vintage Fender® blackface and silverface), as well as Peavey® and Switchcraft® 1/4" jacks.  Does NOT fit the 24mm Marshall® pots.  
Part #JNUT-38
$0.89
(Set of 1 washer and 1 nut)
 


Click on photo for
larger view
SWITCH, TOGGLE - MADE BY CARLING - RATED AT 15A, 125VAC.    Two position (on/off), double pole (DPST).   Fits 1/2" chassis hole.   1/4" push on terminals.     Original Fender® part number 003657000 (old number 036570).    Used as the power switch in the Blues Junior.
Part #SW-525
$6.95  


Click on photo for
larger view
ORIGINAL Fender® PUSH SWITCH
DPDT Mini Short-Throw Push Switch.  Has 6 electrical terminals on bottom of switch (DPDT).  Used as the 'Fat' switch push switch in the Blues Junior.  Original Fender® part number 002809100.   Also Fender® part number 028091, and 028091049.   Button not included, see K-058 below
Part #SW-028
$4.95  


Click on photo for
larger view
BUTTON, for push switch, Black.  This black button pushes onto the switch stem of the 'Fat' switch in the Blues Junior.  Original Fender® part number 0028104000.   Button only - not the complete switch.  See the SW-028 switch above.
Part #K-058
$2.99  



Click on photo for
larger view
Fender® VINTAGE STYLE GUITAR AMP HANDLE, RAISED, OXBLOOD STITCHED LEATHER.  Oxblood (reddish-brown) handle strap, made of genuine leather, replacement for Fender® "tweed" style amps (as well as other vintage amps).  Has slight "raised" bump near the center of the handle.   Oxblood, white stitched.  6.5 inches from mounting center to mounting center.    Comes complete with two nickel-plated handle mounts and four screws.  Perfect for restoring that vintage amp in your closet!
Part #GAH-382
$14.99  




Click on photo for
larger view
Fender® STYLE GUITAR AMP HANDLE, RAISED, BROWN STITCHED IMITATION LEATHERBrown handle strap, replacement for Fender® "tweed" style amps (as well as other vintage amps.  Has slight "raised" bump near the center of the handle.   Brown "pleather", white stitched.  6.5 inches from mounting center to mounting center.    Comes complete with two nickel-plated handle mounts and four screws with T-nuts.   Perfect for restoring that vintage amp in your closet!
Part #GAH-282
$12.99  


BLACK FENDER HANDLE
Click on photo for
larger view
ORIGINAL Fender® GUITAR AMP HANDLE.  Black amplifier handle with vinyl sleeve over steel strap and one-screw mounting nickel-plated end caps.   Includes mounting hardware (two screws and T-nuts).   Used on some versions of the Blues Junior.    Original Fender® part number 0990947000.
Part #FAH-332
$13.99  


Click on photo for
larger view

Fender® VINTAGE HANDLE SCREWS
Pack of 2 stainless steel handle screws for Fender® style FAH-332.  See Data Sheet here
Part #SC-403
$0.99
(for a pack of 2 screws)
 


(Brown)

Click on photo for
larger view
Fender® STYLE GUITAR AMP HANDLEBrown handle strap, "dogbone" style. Chrome end hooks - replacement for vintage and modern Fender® amps.   Replacement for Fender® part number 0990946000.   Used on some versions of the Blues Junior.  Does not contain Fender® logo, so it may be used on other brands of amps.  Color of handle strap is brown.   Screws not included - order screw pack SC-402 separately (takes a pack of 4 screws).
Part #FAH-328
$6.99  


(Black)

Click on photo for
larger view
Fender® STYLE GUITAR AMP HANDLEBlack handle strap, "dogbone" style. Chrome end hooks - replacement for vintage and modern Fender® amps.  Replacement for Fender® part number 0990943000.   Used on some versions of the Blues Junior.  Does not contain Fender® logo, so it may be used on other brands of amps.  Color of handle strap is black.  Screws not included - order screw pack SC-402 separately (takes a pack of 4 screws).
Part #FAH-329
$6.99  


Click on photo for
larger view

Fender® "DOGBONE" HANDLE SCREWS
Pack of 4 chrome "Dogbone" handle screws for Fender® style FAH-328 and FAH-329 handles.   Fits the handle on the Fender® Blues Junior versions that used the "dogbone" style handle.  8-32 thread.
Part #SC-402
$1.59
(for a pack of 4 screws)
 


Click on photo for
larger view

Fender® STAINLESS STEEL BACK-PANEL SCREWS
Pack of 6 stainless steel back panel screws for Fender® original and reissue "Tweed" series amps.   Fits the Fender® Hot Rod Deluxe, Hot Rod Deville, Blues Deluxe, Blues Junior and Blues Deville, 59 Bassman reissue, as well as the original Tweed amps from the 1950s:   Tweed Vibrolux, Tweed Twin, Tweed Tremolux, Tweed Super, Tweed Pro, Tweed Princeton, Tweed Harvard, Tweed Deluxe, Tweed Champ, and Tweed Bassman.   3/4" long, 10-32 thread.    Fender® Original Part number 0015990049.   Pack of 6 screws.
Part #FBP-6
$2.99
(for a pack of 6 screws)


Click on photo for
larger view

Fender® STAINLESS STEEL CHASSIS MOUNTING SCREWS
Pack of 6 stainless steel chassis mounting screws for Fender® reissue "Tweed" series amps.   Mounts the chassis to the cabinet on top as well as the sides of the cabinet.  Fits the Fender® Hot Rod Deluxe, Hot Rod Deville, Blues Deluxe, Blues Junior, Pro Junior, and Blues Deville, 59 Bassman reissue. 1 1/2" long, 10-32 thread.    Fender® Original Part number 0036619049.   Pack of 6 screws.
Part #FCM-6
$2.99
(for a pack of 6 screws)



Click on photo for
larger view
SPEAKER BAFFLE MOUNTING BRONZE SCREWS AND STAINLESS STEEL KEPS NUTS (SET OF 4) FOR Fender® TWEED AMPS.   Set of 4 screws, bronze 6-32, 1 1/2 inches long, Phillips and matching 6-32 Keps Nuts with integral washers.   This set of four bronze screws connects the speaker baffle board to the cabinet on Fender® tweed combo amps from the 50s, as well as today's reissue tweed amps such as the Hot Rod Deluxe and 59 Bassman Reissue.    Replaces Fender part number 036618 or 0036618049.   For amps which require additional baffle screws, see the individual screw/nut part number SC-415, below.
Part #SC-415-4
$3.99
(for a pack of 4 screws and 4 nuts)



Click on photo for
larger view
SPEAKER BAFFLE MOUNTING BRONZE SCREW AND STAINLESS STEEL KEPS NUT FOR Fender® TWEED AMPS.  Individual screw, bronze 6-32, 1 1/2 inches long, Phillips and matching 6-32 Keps Nut with integral washer.   These screws connect the speaker baffle board to the cabinet on Fender® tweed combo amps from the 50s, as well as today's reissue tweed amps such as the Hot Rod Deluxe and 59 Bassman Reissue.    Replaces Fender part number 036618 or 0036618049.
Part #SC-415
$1.09
(for a single screw with nut)
 


Set of 4 screws shown.  Set of 5 screws also available.

Click on photo for
larger view

SPEAKER BAFFLE MOUNTING STAINLESS STEEL SCREWS AND STAINLESS STEEL KEPS NUTS (SETS OF 4 OR 5) FOR Fender® BLUES DELUXE, BLUES DEVILLE, BLUES JUNIOR III, HOT ROD DELUXE OR HOT ROD DEVILLE AMPS WITH BLACK TOLEX.   Sets of either 4 or 5 screws, stainless steel 6-32, 1 1/2 inches long, flat stainless washers, Phillips and matching 6-32 Keps Nuts with integral washers.   This set of four chrome style screws connects the speaker baffle board to the cabinet on Fender® amps.   Blues Junior III needs the 4-screw set, other larger amps with black tolex need the 5-screw set.   Replaces Fender part number 050858 or 0050858000.   For amps covered in Tweed Tolex, see the SC-415 screws.
Part #SC-414-X
4-screw set:
$2.79

5-screw set:
$3.29
Select Option:


Quantity:


Click on photo for
larger view
Fender® Amp Tweed Block Logo
Fender® tweed amp logo includes mounting pins and is designed for the Blues Junior™
.  Approx. 2 15/16" wide and 7/8" tall.   Original Fender® part number 0994096000.
Part #FAL-917
$10.99
(each)
 


Click on photo for
larger view
Fender® 8 ft POWER CORD, 3-WIRE, 18ga, SJT type, .250 TAB ends.   Black and White wires terminated in 1/4 inch push on terminals.   Green wire terminated in screw terminal for ground connection to chassis.  Cord length 8 feet, cord thickness is 0.29 inches (about 9/32" or 7.3mm).   Fender® part number 0026541049.    The power cord as used in North America only on the Blues Junior.  Standard NEMA 5-15 plug for North American use at 110-120 Volts AC.   Used only in North America.
Part #026541
$12.95  


Click on photo for
larger view
EXTRA-LONG 12 ft POWER CORD, 3-WIRE, 18ga, SJT type, .250 TAB ends.   Black and White wires terminated in 1/4 inch push on terminals.   Green wire terminated in screw terminal for ground connection to chassis.  Cord length 12 feet, cord thickness is 0.30 inches (about 9/32" or 7.3mm).   Replaces Fender® part number 0026541049 with a longer 12 ft cord option for more convenience.    Longer cord for the Fender® Vibrosonic, Custom Vibrolux, Ultimate Chorus, Rumble Bass, Hot Rod Deluxe, Hot Rod Deville, Blues Deluxe, Blues Deville, Blues Junior, Acoustasonic SFX, 65 Twin Reverb Reissue, 65 Deluxe Reverb Reissue, BXR200, 57 Twin Amp Reissue   Standard NEMA 5-15 plug for North American use at 110-120 Volts AC.   Used only in North America.
Part #026541-12
$16.95  


Click on photo for
larger view
Fender® style reverb or AC cable clamp.   Used on Fender amps since the early 60s to hold the reverb cable to the side of the cabinet.   Clamp is 3/8" diameter, comes with 3/4" screw for mounting.  Also used in some amplifiers to hold the AC cord to the cabinet wall.  Fender part number 022941.   Works on many other brands of amplifiers as well.
Part #
RCC-381
$0.99  


Click on photo for
larger view
LARGE SIZED STRAIN RELIEF FOR 35/64" X 5/8" HOLE
Popular strain relief found on most vintage guitar amplifiers with round power cords, including most vintage Fender® amps.   Designed for 5/16" cord diameter.   Click here for specific dimensions of chassis hole.   For a strain relief removal / installation tool to make the job much easier, see the YTH-205 below.
Part #SR-1200
$0.99


Click on photo for
larger view
STRAIN RELIEF INSTALLATION/REMOVAL TOOL
Removing and installing strain reliefs can be a frustrating job.   Standard pliers just don't get the job done and can damage the strain relief.   These special strain relief pliers are just what you need.  They fit perfectly on AC power cord strain reliefs and give you the leverage you need to compress the strain relief for easy removal and installation, without damage.
Part #YTH-205
$10.95

MDL-2 
(Sold in packs of five fuses.  
1 1/4" long x 1/4" diameter)

FUSE,  Fender® 2A Slow-Blow. Rated at 2A, for use with Blues Junior in North America (120V).

Part #MDL-2

$4.95 (Pack of 5 fuses)



Click on photo for larger view

Revisit™ Reverb Tank, 9" long, 3 spring, equivalent to Accutronics 8EB2C1BShort Tank, Medium Decay, input impedance 800 ohms, output 2575 ohms, insulated input and grounded output. Mounts horizontal, open side down.   Used  in Fender® Blues Junior.  Relaces Fender® part number 0028055000.

View the 3-year warranty details here.
Part #8EB2C1B

"Bringing back the sound of vintage Accutronics tanks"

$29.99
In Stock
 


Click on photo for
larger view
Fender® Reverb Cable. Molded plastic dual RCA on one end, jacketed wires with braided shields on the other. 30 inches long.  This cable is used on the Blues Junior.   Fender® part number 0028577000.
Part #RC-311
$5.95  


Click on photo for
larger view
TUBE SOCKET FOR MINIATURE 9-PIN TUBES.  PC MOUNT, MICALEX.    9 pin ceramic PC mount socket, stand-off mounting, 3/4" diameter, 3/4" tail diameter.  For bottom mounting (mounted from the inside of the chassis, below the chassis hole).   Fits 12AX7, 12AU7, 12AT7, 6BQ5, EL84 tubes.    Micalex replacement for the tube sockets in the Fender® Blues Junior, Pro Junior, and the Fender® Hot Rod Deluxe/Deville and Blues Deluxe/Deville.  Fender part number 0029167049.
Part #TS-9-620
$1.99


Click on photo for
larger view
3-PACK, TUBE SOCKET FOR MINIATURE 9-PIN TUBES.  PC MOUNT, MICALEX.    9 pin ceramic PC mount socket, stand-off mounting, 3/4" diameter, 3/4" tail diameter.  For bottom mounting (mounted from the inside of the chassis, below the chassis hole).   Fits 12AX7, 12AU7, 12AT7, 6BQ5, EL84 tubes.  Fender part number 0029167049.    This 3-pack replaces all of the sockets for the 12AX7 preamp tubes in the Fender® Blues Junior, Hot Rod Deluxe/Deville and Blues Deluxe/Deville.
Part #TS-9-620-3
$4.99
(for a 3-pack of tube sockets)


Click on photo for
larger view
5-PACK, TUBE SOCKET FOR MINIATURE 9-PIN TUBES.  PC MOUNT, MICALEX.    9 pin ceramic PC mount socket, stand-off mounting, 3/4" diameter, 3/4" tail diameter.  For bottom mounting (mounted from the inside of the chassis, below the chassis hole).   Fits 12AX7, 12AU7, 12AT7, 6BQ5, EL84 tubes.    Fender part number 0029167049.    This 5-pack replaces all 5 tube sockets in the Fender® Blues Junior.
Part #TS-9-620-5
$7.95
(for a 5-pack of tube sockets)


Click on photo for
larger view
10-PACK, TUBE SOCKET FOR MINIATURE 9-PIN TUBES.  PC MOUNT, MICALEX.    9 pin ceramic PC mount socket, stand-off mounting, 3/4" diameter, 3/4" tail diameter.  For bottom mounting (mounted from the inside of the chassis, below the chassis hole).   Fits 12AX7, 12AU7, 12AT7, 6BQ5, EL84 tubes.    Fender part number 0029167049.    Used in the Fender® Blues Junior, and the Fender® Hot Rod Deluxe/Deville and Blues Deluxe/Deville.
Part #TS-9-620-10
$12.95
(for a 10-pack of tube sockets)


Click on photo for
larger view
TUBE SOCKET FOR MINIATURE 9-PIN TUBES.  PC MOUNT, CERAMIC.    9 pin ceramic PC mount socket, stand-off mounting, 3/4" diameter, 3/4" tail diameter.  For bottom mounting (mounted from the inside of the chassis, below the chassis hole).   Fits 12AX7, 12AU7, 12AT7, 6BQ5, EL84 tubes.    Ceramic replacement for the tube sockets in the Fender® Blues Junior, and the Fender® Hot Rod Deluxe/Deville and Blues Deluxe/Deville.
Part #TS-9-217
$1.49


Strat®, Stratocaster®, Esquire®, Telecaster®, Tele®, Jazzmaster®, Jaguar®, Mustang®, P.Bass®, J.Bass® and Fender® are registered trademarks of Fender® Musical Instruments. The replacement necks and bodies are for a Fender® or Squier® by Fender® guitar or bass. The distinctive headstock designs and the distinctive body designs of the Stratocaster®, Telecaster®, J.Bass®, P.Bass® and Tele® Bass are registered trademarks of Fender® Musical Instruments Co.  
Peavey® is a registered trademark of Peavey® Electronics Corporation.
Marshall® is a registered trademark of Marshall® Amplification Plc.
Mesa Boogie® is a registered trademark of MESA/Boogie® Ltd.
AmpRepairParts.com and Studio Sound Electronics are not affiliated with these companies.
All company names, logos and product names mentioned on these pages are trademarks of their respective owners.

Copyright ©2017 Studio Sound Electronics - All Rights Reserved
Not responsible for web site errors or omissions