Keyboard
Parts

Keyboard
Op Amps, etc

   

Op-Amp, 4558, very common in amplifiers, mixers, power amps.  8-pin DIP
Part #NJM4558-D
$1.00

Low-noise 5532 Dual Op-Amp in 8-pin DIP package.
Part #NE5532
$1.50

Low-noise 5534 Single Op-Amp in 8-pin DIP package.
Part #NE5534
$1.50

Low-noise 2068 Dual Op-Amp in 8-pin DIP package.
Part #NJM2068
$1.50

Low-power version of the TL072 Dual Op-Amp in 8-pin DIP package.  Draws only 400uA.   Great for battery-operated effects - increased battery life.
Part #TL062CP
$2.00

Low-noise, JFET input, TL071Single Op-Amp in 8-pin DIP package.  Also TL071CN.
Part #TL071CP
$1.50

Low-noise, JFET input, TL072 Dual Op-Amp in 8-pin DIP package.  Also TL072CN.
Part #TL072CP
$1.50


4808-3004
From the 3M Company ... 8-pin DIP socket, fits all of the 8-pin op-amps above.   We recommend installing a socket first whenever you replace an op-amp - it makes future repairs much quicker and easier!
#4808-3004
$0.35

+15V 1 amp Voltage Regulator - Metal Tab
Part #7815
$0.90

-15V 1 amp Voltage Regulator - Metal Tab
Part #7915
$0.90

Floppy Drive
Belt

   

Click on photo for
larger view

Floppy disk drive belt.   Exact replacement for the original floppy drives used in the following makes and models:
Korg:  X3, X3R, X2, i2, i3, & i4s
Yamaha:  SY77, SY85, SY99, PSR-SQ16, PSR1700, PSR2700, W5, and W7 keyboards
Yamaha:   MDF2 data filers
Technics: KN2000

Part #FDB-7

$4.95

Jacks

   

Click on photo for
larger view
USB CONNECTOR, "B" type.   USED IN YAMAHA, KORG, ROLAND, Others. Korg part number CON0001079, as found in the Korg SV1-73, and Triton Extreme.  Also found in the Access Virus T1, Akai MPK49 and MPK61, Alesis Q25, Q49, QX25, QX49, Dave Smith Prophet 12, Edirol PCR Series, M-Audio Axiom 49, Axiom Pro 49, Axiom 61, Axiom Pro 61, KeyRig Series, Keystation Series and Key Studio, Roland PCR Series Controllers, and Yamaha MM6, MM8, and S90, as well as other brands and models not listed.  Line 6 part number 21-21-0001, as found in many Line 6 guitar processors.
Part #J-437
$1.29  


Click on photo for
larger view
USB CONNECTOR, "A" type.   USED IN YAMAHA, KORG, ROLAND, Others.   "A" Type USB connector, found in a number of keyboards, processors, professional audio gear made by many manufacturers.   Right-angle PC mount 4-conductor.    Industry standard USB.
Part #J-427
$1.29  

5 PIN MIDI CONNECTOR, PCB   Female, right angle.  Pin spacing 2.54mm (0.1").   2A 100VAC - 1A 24VDC.   Often found in keyboards, rack mount MIDI-controlled processors, etc.
Part #J-1010
$1.95  


Click on photo for
larger view

Note:  Nut & Washer NOT included - reuse original, or order JN-916, below.

JACK, 1/4",  USED IN YAMAHA, KORG, ROLAND, Others. Korg part number 454X851003, Yamaha part number LB202330.  If the back is black, this is NOT the correct replacement, and you may need the J-532, J-533, or J-539 instead.   NOTE:  EARLIER VERSIONS OF THIS JACK HAVE THE REAR TWO CONTACTS SLIGHTLY OFFSET FROM EACH OTHER.   IN THIS REPLACEMENT, THERE IS NO OFFSET.
NUT & WASHER NOT INCLUDED - REUSE ORIGINAL OR ORDER JN-916, BELOW
Part #J-531
$5.75  

   
WITH CHROME SLEEVE
Click on photo for
larger view

Note:  Nut & Washer NOT included - reuse original, or order JN-916.

JACK, 1/4", Marshall® ORIGINAL, MG SERIES, USED AS CD OUTPUT JACK, PC MOUNT,  ALSO USED IN YAMAHA, KORG, ROLAND, ENSONIQ.  CHROME SLEEVE.
Used in certain Marshall® G-series amps from the late 90's - compare with original jack.   Used as the CD input jack in the Marshall® G15RCD and the G30RCD.   Original Marshall® part number J1031.   Used for the Headphone output of the Roland S-50 and S-770 and for the Headphone and Ext. Control jack of the Roland U-220.   It also replaces all the jacks in the Korg 01/W and 01R/W, and the CV Pedal jacks in the Ensoniq ESQ-1, ESQ-M, and SQ-80 keyboards.  The jack is equivalent to Roland part # 13449148 (YKB21-5009), Korg part # 454004400, and Behringer part # W64-01081-03178.   The chrome sleeve at the jack's opening is cosmetic.  The jack will replace equivalent jacks that have a gold sleeve or no sleeve.
NUT & WASHER NOT INCLUDED - REUSE ORIGINAL OR ORDER JN-916, BELOW
Part #J-532
$2.75  

   
WITH GOLD SLEEVE
Click on photo for
larger view

Note:  Nut & Washer NOT included - reuse original, or order JN-916.

JACK, 1/4", Marshall® ORIGINAL, MG SERIES, USED AS CD OUTPUT JACK, PC MOUNT,  ALSO USED IN YAMAHA, KORG, ROLAND, ENSONIQ.  GOLD SLEEVE.
Used in certain Marshall® G-series amps from the late 90's - compare with original jack.   Used as the CD input jack in the Marshall® G15RCD and the G30RCD.   Original Marshall® part number J1031.   Used for the Headphone output of the Roland S-50 and S-770 and for the Headphone and Ext. Control jack of the Roland U-220.   It also replaces all the jacks in the Korg 01/W and 01R/W, and the CV Pedal jacks in the Ensoniq ESQ-1, ESQ-M, and SQ-80 keyboards.  The jack is equivalent to Roland part # 13449148 (YKB21-5009), Korg part # 454004400, and Behringer part # W64-01081-03178.    The gold sleeve at the jack's opening is cosmetic.  The jack will replace equivalent jacks that have a chrome sleeve or no sleeve.
NUT & WASHER NOT INCLUDED - REUSE ORIGINAL OR ORDER JN-916, BELOW
Part #J-532G
$2.25  

   
WITH CHROME SLEEVE

Click on photo for
larger view

Note:  Nut & Washer NOT included - reuse original, or order JN-916.

JACK, 1/4", STEREO, 4-PIN SWITCHED, MADE BY KOBICONN OR JALCO, USED IN  KORG, YAHAMA & OTHERS, PC MOUNT   This 4-pin, PC mount, 1/4" stereo phone jack has a normally closed tip shunt and is used in a variety of amps and keyboards made by Ensoniq, Marshall®, Ibanez, Casio, Korg, Roland and others.   Used in the Ibanez Super Metal SML stomp box, and the Casio Privia PX-310 keyboard.   It also replaces the Ensonq SQ-1, SQ-2 and SQ-R jacks and the Ensoniq ESQ-1 and ESQ-M Output jacks, Tape In & Out jacks, and Sequencer Footswitch jack.    Also replaces the Aviom A16II-HP output jack.

This jack replaces Korg part #454004400 (YKB21-5010) and Roland part #13449263 (YKB21-5005).   The J-533G has a chrome sleeve - for the same jack with a gold sleeve, order J-533G.

NUT & WASHER NOT INCLUDED - REUSE ORIGINAL OR ORDER JN-916, BELOW
Part #J-533
$2.75  

   
WITH GOLD SLEEVE

Click on photo for
larger view

Note:  Nut & Washer NOT included - reuse original, or order JN-916.

JACK, 1/4", STEREO, 4-PIN SWITCHED, MADE BY KOBICONN OR JALCO, USED IN  KORG, YAHAMA & OTHERS, PC MOUNT  This 4-pin, PC mount, 1/4" stereo phone jack has a normally closed tip shunt and is used in a variety of amps and keyboards made by Ensoniq, Marshall®, Ibanez, Casio, Korg, Roland and others.   Used in the Ibanez Super Metal SML stomp box, and the Casio Privia PX-310 keyboard.   It also replaces the Ensonq SQ-1, SQ-2 and SQ-R jacks and the Ensoniq ESQ-1 and ESQ-M Output jacks, Tape In & Out jacks, and Sequencer Footswitch jack. 

This jack replaces Korg part #454004400 (YKB21-5010) and Roland part #13449263 (YKB21-5005).   The J-533G has a gold sleeve - for the same jack with a chrome sleeve, order J-533.

NUT & WASHER NOT INCLUDED - REUSE ORIGINAL OR ORDER JN-916, BELOW
Part #J-533G
$2.75  


WITH CHROME SLEEVE
Click on photo for
larger view

Note:  Nut & Washer NOT included - reuse original, or order JN-916.

JACK, 1/4", MONO, 3-PIN, INPUT, MADE BY KOBICONN,    Used in Marshall®, Korg, Yamaha, Roland & others, PC Mount.  Chrome sleeve around jack entrance.   Gold sleeve also available, see J-539.  Korg part number 454004300.
NUT & WASHER NOT INCLUDED - REUSE ORIGINAL OR ORDER JN-916, BELOW
Part #J-539
$4.99  


WITH GOLD SLEEVE
Click on photo for
larger view

Note:  Nut & Washer NOT included - reuse original, or order JN-916.

JACK, 1/4", MONO, 3-PIN, INPUT, MADE BY KOBICONN
Used in Marshall®, Korg, Yamaha, Roland & others, PC Mount.  Gold sleeve around jack entrance.   Chrome sleeve also available, see J-539.   Korg part number 454004300.

NUT & WASHER NOT INCLUDED - REUSE ORIGINAL OR ORDER JN-916, ABOVE.
Part #J-539G
$4.99



Click on photo for
larger view

Note:  Nut & Washer NOT included - reuse original, or order JN-916.

JACK, 1/4", 7-PIN, HEADPHONE,  USED IN Marshall® , YAMAHA & OTHERS, PC MOUNT
Used as the headphone jack in the Marshall® G15RCD and G30RCD.   Original Marshall® part number V4550.   Used as the headphone jack in Yamaha models YPR6, HE6, PSR520, YPR8, and other models.   Original Yamaha part number LB10187R.   Used in the Korg Triton Studio, Triton extreme, M3, CI8600, CI9600.  Korg part number 454005600, YKB21-5006.   Casio Part # 36120665.

NUT & WASHER NOT INCLUDED - REUSE ORIGINAL OR ORDER JN-916, BELOW
Part #J-540
$5.95  


Click on photo for
larger view

Note:  Nut NOT included - reuse original, or order J-5NT, below.

JACK, 1/4", STEREO, REAN TYPE, PC MOUNT, Half-thread (Bullnose)
PCB mount 1/4" jack. Stereo, 6 pin. Has short 'bullnose' threads, and often mounted so that a nut may not be needed.   Korg part number CON0010058.  Nut NOT included.  
NUT NOT INCLUDED - REUSE ORIGINAL OR ORDER J-5NT BELOW
Part #J-562

$ 3.95


Click on photo for
larger view

DC POWER JACK
Replacement Barrel DC power jack for many pedals, keyboards, etc which use a PC board mounted DC power jack.  Connector fits the popular 2.1mm x 5.5mm barrel plug found on many Adapters.   Normally closed switch, so that an internal battery may be switched on or off automatically as the Adapter is connected.   Plastic housing isolates both conductors, so it may be used for either center positive or center negative Adapters. 
Part #BJK-118
$0.99  

NUT AND WASHER, CHROME, KOBICONN OR JALCO TYPE.
Fits J-506, J-506A, J-507, J-530, J-531, J-532, J-532G, J-533, J-533G, J-539, J-539G, J-540, J-545, J-6074, J-6075, J-560  
Part #JN-916

$0.79

SAVE WITH MULTIPACK!  NUT AND WASHER, CHROME, KOBICONN OR JALCO TYPE, SET OF 6.
Fits J-506, J-507, J-530, J-531, J-532, J-532G, J-533, J-533G, J-539, J-539G, J-540, J-545, J-6074, J-6075, J-560.   Set of 6 JN-916 nuts with washers
Part #JN-916-6

$3.59
(For set of 6 nuts and 6 washers)


Click on photo for
larger view
JACK NUT, PLASTIC, GENUINE CLIFF UK, REPLACEMENT FOR Marshall® AND OTHERS.   Note:     Replaces most black plastic jack nuts EXCEPT for Roland.    Will NOT fit Roland jacks.
Replacement jack nut as found on the J-502, J-503, J-504, J-505, J-503L and J-504L jacks.   Also fits the J-518, J-562 and J-519 jacks.
 Part #J-5NT
$0.50  

Key Contact
Strip
 

   

Click on photo for
larger view
Key Contact Strip, used in many brands and models of keyboards.    One strip handles one octave of keys (12 notes)   Fits only the following makes and models:
Access: Virus Series
Alesis: Andromeda, Ion, QS Series
Doepfer: LMK2+
E-Mu: E4K, E4XT, E-synth
Ensoniq: ASR-88, E-prime, Fizmo, KS-32, KT-76, KT-88, MR-61, MR-76, MR Rack, SQ-2, ZR-76
Gem: Equinox, Pro 1
Ketron: Vega
Korg:  Bx3, Cx3, i1, i4, i4s, i5s, iS series, ix3000, Karma, MS 2000 series, N series, Prophecy, SP 100, SP 200, SP 300, SP 500, TR series, Triton LE, Triton Studio 88, Triton Extreme 88, X2, X5, X5D, XC1000, XC2000, XC3000
Kurzweil: K2000, K2500, K2500X, K2600X, KME61, Mark series, PC series, RG series, SP-88
Moog: Minimoog Voyager
Nord: Electro series, Lead 1, Lead 2, Lead 2X, Lead 3, Modular, Modular G2, Modular G2X
Novation: Bass Station, K-Station, KS4, KS5, SL series, X-Station
Roland: A-33, A-37, A-50, AX-1, AX-7, D-20, D-50, E-5, E-14, E-16, E-35, E-36, E-38, E-70, E-500, EM-10, EM-15, EM-20, EM-25, EM-55, EM-2000, EP-75, G-70, G-800, G-1000, HP-126, HP-136, HS-80, Juno-2, KR-33 (early models), MKB-200, PC-160A. PC-180A, PC- 200 Mk II, PC-300, Pro-E, RD-100, RD-170, S-10, S-50, VA-7, W-30
Part #KCS-12
$12.95  

Keyboard Power Cords

   

Click on photo for
larger view
Revisit™ 6 ft POWER CORD, DETACHABLE, 3-WIRE, 18ga, 6 ft LONG, IEC CONNECTOR AT EQUIPMENT END.  Common replacement power cord for many keyboards - 6 feet long.  Standard NEMA 5-15 plug for North American use at 110-120 Volts AC.    IEC connector at equipment end.   Used only in North America.
Part #PC-300
$5.95  


Click on photo for
larger view
Revisit™ 10 ft POWER CORD, DETACHABLE, 3-WIRE, 18ga, 10 ft LONG, IEC CONNECTOR AT EQUIPMENT END.  Common replacement power cord for many keyboards - 10 feet long.   Extra length allows more flexibility in equipment placement, reduces use of extension cords.  Standard NEMA 5-15 plug for North American use at 110-120 Volts AC.    IEC connector at equipment end.   Used only in North America.
Part #PC-600
$10.95  


Strat®, Stratocaster®, Esquire®, Telecaster®, Tele®, Jazzmaster®, Jaguar®, Mustang®, P.Bass®, J.Bass® and Fender® are registered trademarks of Fender® Musical Instruments. The replacement necks and bodies are for a Fender® or Squier® by Fender® guitar or bass. The distinctive headstock designs and the distinctive body designs of the Stratocaster®, Telecaster®, J.Bass®, P.Bass® and Tele® Bass are registered trademarks of Fender® Musical Instruments Co.  
Peavey® is a registered trademark of Peavey® Electronics Corporation.
Marshall® is a registered trademark of Marshall® Amplification Plc.
Mesa Boogie® is a registered trademark of MESA/Boogie® Ltd.
AmpRepairParts.com and Studio Sound Electronics are not affiliated with these companies.
All company names, logos and product names mentioned on these pages are trademarks of their respective owners.

Copyright ©2017 Studio Sound Electronics - All Rights Reserved
Not responsible for web site errors or omissions