Marshall®
Knobs

We carry a complete selection of Marshall® Amplifier parts for both vintage and modern amps.

Back to Marshall® Amp Parts Index



Click on photo for
larger view
KNOB, Original Marshall®, PUSH ON KNURLED
Standard original Marshall® control knob, push-on type.  Designed for the "knurled" split-shaft potentiometers. Found on a variety of Marshall® amps, including most JCM-800, JCM-900, JTM-30 series, JTM-60 series, JCM-600 series, 9001 and 9004 preamp, the early ValveState models (8010, 8020, 8040, 8080, 8100, 8200, 8240, 8280) and the earlier MG series versions as well as other models.  Original Marshall® part.   Note:   In most cases, the gold color on the new knob will be deeper than the other old knobs on your amp - the gold caps on Marshall® knobs fade over time.   Especially true if your amp is ~20 years old.

Note:  Marshall® recently switched to a new subcontractor to produce these knobs (late in 2016).   These new knobs are (1) more of an "orangey" shade of gold than the previous Marshall® knobs and (2) the gold caps have more of a matte finish than the previous caps which were shinier.  These new Marshall® knobs are unfortunately less likely to match the existing knobs on your amplifier.
Part #MKPT

$2.99
(Single Knob)


Click on photo for
larger view
KNOB SET, Original Marshall®, PUSH ON KNURLED, SET OF 6.   Standard original Marshall® control knob, push-on type.  Designed for the "knurled" split-shaft potentiometers. Found on a variety of Marshall® amps, including most JCM-800, JCM-900, JTM-30 series, JTM-60 series, JCM-600 series, 9001 and 9004 preamp, the early ValveState models (8010, 8020, 8040, 8080, 8100, 8200, 8240, 8280) and the earlier MG series versions as well as other models.  Original Marshall® part.   Note:   In most cases, the gold color on the new knob will be deeper than the other old knobs on your amp - the gold caps on Marshall® knobs fade over time.   Especially true if your amp is ~20 years old.

Note:  Marshall® recently switched to a new subcontractor to produce these knobs (late in 2016).   These new knobs are (1) more of an "orangey" shade of gold than the previous Marshall® knobs and (2) the gold caps have more of a matte finish than the previous caps which were shinier.  These new Marshall® knobs are unfortunately less likely to match the existing knobs on your amplifier.
Part #MKPT-6

$12.95
(Set of 6 knobs)


Click on photo for
larger view
KNOB SET, Revisit™ Quality Reproduction of Marshall® Knob, Push-on Knurled, Single Knob. Excellent quality aftermarket Marshall® control knobs, push-on type.   Designed for the "knurled" type control shafts.   Found on a variety of Marshall® amps, including most JCM-800, JCM-900, JTM-30 series, JTM-60 series, JCM-600 series, 9001 and 9004 preamp, the early ValveState models (8010, 8020, 8040, 8080, 8100, 8200, 8240, 8280) and the earlier MG series versions as well as other models. Note:   In most cases, the gold color on the new knob will be deeper than the other old knobs on your amp - the gold caps on Marshall® knobs fade over time.   Especially true if your amp is ~20 years old or greater (JCM800 and JCM900, for example).     Since Marshall® has recently changed the appearance of their original Marshall® brand knobs (duller and more of an orange-gold color), we believe these reproduction knob are now actually closer in appearance to the original Marshall® knobs.
Part #MKCPT
$1.89
(Single Knob)


Click on photo for
larger view
KNOB SET, Revisit™ Quality REPRODUCTION of Marshall® Knobs, Push-on Knurled, Set of 6.   Excellent quality aftermarket Marshall® control knobs, push-on type, set of 6 knobs.  Designed for the "knurled" split-shaft potentiometers. Found on a variety of Marshall® amps, including most JCM-800, JCM-900, JTM-30 series, JTM-60 series, JCM-600 series, 9001 and 9004 preamp, the early ValveState models (8010, 8020, 8040, 8080, 8100, 8200, 8240, 8280) and the earlier MG series versions as well as other models.    Note:   In most cases, the gold color on the new knob will be deeper than the other old knobs on your amp - the gold caps on Marshall® knobs fade over time.   Especially true if your amp is ~20 years old.  Since Marshall® has recently changed the appearance of their original Marshall® brand knobs (duller and more of an orange-gold color), we believe these reproduction knobs are now actually closer in appearance to the original Marshall® knobs.
Part #MKCPT-6
$9.95
(Set of 6 knobs)



Click on photo for
larger view
KNOB SET, Revisit™ Quality REPRODUCTION of Marshall® Knobs, Push-on Knurled, Set of 10.   Excellent quality aftermarket Marshall® control knobs, push-on type, set of 10 knobs.   Designed for the "knurled" split-shaft potentiometers. Found on a variety of Marshall® amps, including most JCM-800, JCM-900, JTM-30 series, JTM-60 series, JCM-600 series, 9001 and 9004 preamp, the early ValveState models (8010, 8020, 8040, 8080, 8100, 8200, 8240, 8280) and the earlier MG series versions as well as other models.     Nothing perks up the tired looks of a road-worthy Marshall® like a complete new set of knobs.   Older Marshalls typically have knobs where some of the gold caps have fallen off, and the other gold caps have faded to look more like silver than gold.    It used to be a bit pricey to swap out the complete set of knobs on some of the JCM900's, but with this new set of aftermarket Marshall® knobs, it's affordable.    This set of 10 knobs is perfect for many JCM900 series models with 10 control pots, such as the 2101, 2501, 4100, 4101, 4102, 4500, 4501, and 4502.   Quality reproduction of the original Marshall® knobs at half of the cost.  Since Marshall® has recently changed the appearance of their original Marshall® brand knobs (duller and more of an orange-gold color), we believe these reproduction knobs are now actually closer in appearance to the original Marshall® knobs.
Part #MKCPT-10
$14.95
(Set of 10 knobs)



Click on photo for
larger view
KNOB SET, Revisit™ Quality REPRODUCTION of Marshall® Knobs, Push-on Knurled, Set of 11.   Excellent quality aftermarket Marshall® control knobs, push-on type, set of 11 knobs.  Designed for the "knurled" type control shafts (used on most JCM800s - check your particular amp to make sure it has knurled knobs and not solid smooth shaft pots with set-screw knobs).     Nothing perks up the tired looks of a road-worthy Marshall® like a complete new set of knobs.   Older Marshalls typically have knobs where some of the gold caps have fallen off, and the other gold caps have faded to look more like silver than gold.    It used to be a bit pricey to swap out the complete set of knobs on some of the split-channel JCM800's with 11 controls, but with this new set of aftermarket Marshall® knobs, it's affordable.    This set of 11 knobs is perfect for many split-channel JCM800 series models with 11 control pots, such as the 2205, 2210, 4210, 4211, 4212, 5210, and 5212.  (Check your particular amp to make sure it has knurled knobs and not solid smooth shaft pots with set-screw knobs)  Quality reproduction of the original Marshall® knobs at half of the cost.  Since Marshall® has recently changed the appearance of their original Marshall® brand knobs (duller and more of an orange-gold color), we believe these reproduction knobs are now actually closer in appearance to the original Marshall® knobs.
Part #MKCPT-11
$15.95
(Set of 11 knobs)



Click on photo for
larger view
KNOB SET, Economy-priced REPRODUCTION of Marshall® Knobs, Push-on Knurled, Set of 10.   Economy-priced aftermarket Marshall® control knobs, push-on knurled type, set of 10 knobs.   Designed for the "knurled" split-shaft potentiometers.   Found on a variety of Marshall® amps, including most JCM-800, JCM-900, JTM-30 series, JTM-60 series, JCM-600 series, 9001 and 9004 preamp, the early ValveState models (8010, 8020, 8040, 8080, 8100, 8200, 8240, 8280) and the earlier MG series versions as well as other models.   No set screw, will not work on smooth shaft pots.  

Comments on appearance:  The gold cap color is a light to medium gold (champagne color), making it close to the original Marshall color.   The finish on the top of the cap is smooth, rather than ridged like the originals.  However, this difference is only noticeable upon close insepction.   Color of the knob base is black.   The quality of the knob is quite good, and they are durable.  Economically priced, making a complete change-out of knobs very affordable.

Part #MKPE-10

$7.95
(Set of 10 knobs)


Click on photo for
larger view
KNOB, Marshall®, PUSH ON D-SHAFT (Read applicable models!)
Standard original Marshall® control knob, push-on type, for D-Shaft pots used in the following Marshall® amp models:   DSL-50 Head, DSL-100 Head, TSL-60 Head, JVM-205C Combo, JVM-210C Combo, JVM-215C Combo, JVM-410C Combo, MA-50H Head, MA-100H Head.  Original Marshall® part.   For the similar knob used on some ValveState models, DSL and TSL combos, MA Series Combos, and JVM series heads, see the MKDS-C knob elsewhere on this page.

Part #MKDS
$2.99
(Single Knob)



Click on photo for
larger view
Save with Multipack!  KNOB, Set of 6 Marshall®, PUSH ON D-SHAFT (Read applicable models!)
Standard original Marshall® control knob, push-on type, for D-Shaft pots used in the following Marshall® amp models:   DSL-50 Head, DSL-100 Head, TSL-60 Head, JVM-205C Combo, JVM-210C Combo, JVM-215C Combo, JVM-410C Combo, MA-50H Head, MA-100H Head.  Original Marshall® part.   For the similar knob used on some ValveState models, DSL and TSL combos, MA series combos and JVM series heads, see the MKDS-C knob elsewhere on this page.

Part #MKDS-6
$14.95
(Set of 6 knobs)



Click on photo for
larger view
KNOB, Marshall®, PUSH ON D-SHAFT (Read applicable models!)

Standard original Marshall® control knob, push-on type, for D-Shaft pots used in the following Marshall® amp models:   DSL-201 combo, DSL-401 combo, TSL-122 combo, TSL-601 combo, TSL-602 combo, JVM205H head, JVM210H head, JVM410H head, VS15 combo, VS30R  combo, VS65R combo, VS100R combo, VS100RH head, VS102R combo, VS230 combo, VS265 combo, AS100D combo, MA50C Combo, MA100C Combo.     Original Marshall® part.   For the similar knob used on DSL and TSL JCM2000 series heads, MA series heads, and JVM series combos see the MKDS knob elsewhere on this page.  
Part #MKDS-C

$3.50
(Single Knob)



Click on photo for
larger view
KNOB, Revisit™ Quality REPRODUCTION of Marshall®, Set Screw.
Revisit™ aftermarket Marshall® control knob, with gold cap and set screw.  Fits 1/4" shaft.  Similar to original Marshall® set-screw knob.  This style of knob was used mainly in the 60s and 70s, and some JCM800 models from the early 80s. 

Comments on appearance and construction:  In most cases, the gold color on the new knob will be deeper than the other old knobs on your amp - the gold caps on Marshall® knobs fade over time.  Since Marshall has recently changed the appearance of their original Marshall brand knobs (duller and more of an orange-gold color), we believe these reproduction knobs are now actually closer in appearance to the original Marshall knobs.   These knobs have a brass insert, so they tend to be more durable than the genuine all-plastic Marshall knobs.
Part #MKSS

$1.99
(Single Knob)
 


Click on photo for
larger view
KNOB SET, Marshall® type, Set Screw, Set of 6.
Revisit™ aftermarket Marshall® control knobs, with gold cap and set screw.  Fits 1/4" shaft, set of 6 knobs.  Similar to original Marshall® set-screw knob.   This style of knob was used mainly in the 60s and 70s and some JCM800 models from the early 80s. 

Comments on appearance and construction:  In most cases, the gold color on the new knob will be deeper than the other old knobs on your amp - the gold caps on Marshall® knobs fade over time.  Since Marshall has recently changed the appearance of their original Marshall brand knobs (duller and more of an orange-gold color), we believe these reproduction knobs are now actually closer in appearance to the original Marshall knobs.   These knobs have a brass insert, so they tend to be more durable than the genuine all-plastic Marshall knobs.
Part #MKSS-6

$8.95
(Set of 6 knobs)
 


Click on photo for
larger view
KNOB, Tall Vintage Marshall® type, SET SCREW
Vintage aftermarket Marshall® control knob, with set screw.  Fits 1/4" shaft.   Taller than the later Marshall® gold knobs - this one is 3/4" tall.  
Part #MKSSV
$3.79
(Single Knob)
 


Click on photo for
larger view
KNOB, Silver Marshall® type, SET SCREW
Revisit™ aftermarket Marshall® control knob, with silver cap and set screw.  Fits 1/4" shaft.  Similar to original silver Marshall® set-screw knob, which has been discontinued.  
Part #MKSSS
$1.99
(Single Knob)
 


Click on photo for
larger view
KNOB, Silver Marshall® type, PUSH ON
Revisit™ aftermarket Marshall® control knob, with silver cap and designed to fit a "knurled" 1/4" shaft.   No set-screw. Similar to original silver Marshall® knob, which has been discontinued.  
Part #MKSPT
$1.99
(Single Knob)
 


Click on photo for
larger view
KNOB, Tall Vintage Marshall® Silver, SET SCREW
Marshall® control knob, silver cap, set-screw type. Taller than the Marshall® MKSSS silver knobs - this one is 3/4" tall.  Used in the Marshall® "Jubilee" series of amps.

Part #K-342
$4.50
(Single Knob)
 


Click on photo for
larger view
KNOB, Marshall® IBS BASS, PUSH ON
Marshall® control knob, black with white line.   Used on the Integrated Bass System (IBS) Bass amps made by Marshall from 1985 through 1993.  

Note:   This is a genuine Marshall replacement knob, but it is slightly different than the original knobs which came on the IBS amps.   The white line is slightly shorter, and the outside of the knob is not as "knurled" as the originals.   This is the current available knob that Marshall® offers for the IBS bass series.   Original Marshall® part number MKB.
Part #MKB
$4.25
(Single Knob)
 


Click on photo for
larger view
KNOB, Generic
A great replacement knob for many styles of amp.  A fairly good choice for use on the Marshall® IBS Bass Amps, at an affordable price.
Part #K-219
$2.95  


Click on photo for
larger view
SQUARE SWITCH CAP - FITS SW-212
This is a black 5mm x 5mm (approx 3/16") square mini-switch cap which fits the SW-212 Marshall® Push Switch (used primarily for channel switching).  Replaces the original S213 switch cap from Marshall® , which has now been discontinued.   NOTE:   This is NOT the power switch cap on ValveState Amps.   This square cap is found on the Marshall®, 6100, 6101, JMP1, JCM600, JCM602, JTM310, JTM312, JTM610, JTM612, JTM615, JTM622, 8010, AS80R, 8010, 8020, 8040, 8080, 8100, 8200, 8240, 8280, and 9004 models.

Part #K-213
$1.50  


Strat®, Stratocaster®, Esquire®, Telecaster®, Tele®, Jazzmaster®, Jaguar®, Mustang®, P.Bass®, J.Bass® and Fender® are registered trademarks of Fender® Musical Instruments. The replacement necks and bodies are for a Fender® or Squier® by Fender® guitar or bass. The distinctive headstock designs and the distinctive body designs of the Stratocaster®, Telecaster®, J.Bass®, P.Bass® and Tele® Bass are registered trademarks of Fender® Musical Instruments Co.  
Peavey® is a registered trademark of Peavey® Electronics Corporation.
Marshall® is a registered trademark of Marshall® Amplification Plc.
Mesa Boogie® is a registered trademark of MESA/Boogie® Ltd.
AmpRepairParts.com and Studio Sound Electronics are not affiliated with these companies.
All company names, logos and product names mentioned on these pages are trademarks of their respective owners.

Copyright ©2017 Studio Sound Electronics - All Rights Reserved
Not responsible for web site errors or omissions