Marshall®
Switches

We carry a complete selection of Marshall® Amplifier parts for both vintage and modern amps.

Back to Marshall® Amp Parts Index



Click on photo for
larger view
ROCKER SWITCH, LIGHTED POWER, ORIGINAL Marshall® , FOUND IN Marshall® JCM900  SERIES
For JCM900 series.  For most JCM800 models, see the SW-492 below.  For JCM2000 and JVM models, see the SW-493 below.   Has 4 electrical terminals on back of switch.   1/4" push-on terminals, or solder directly to terminals.   Rated 22A @ 125VAC, 16A @ 250VAC. 15/16" x 1 1/16" x 1" deep.  Internal neon lamp powered by 125VAC.  Does your old Marshall® power switch from the JCM800 era have five terminals?   See the SW-492 below, instead.
Part #SW-491
$8.95  


Click on photo for
larger view
ROCKER SWITCH, LIGHTED POWER, Revisit™ REISSUE, FOUND IN Marshall® JCM800 SERIES  
Most JCM800 series power switches have 5 terminals on the back of the switch.   For those switches with 5 terminals, this is the correct replacement.   Marshall® no longer offers the original 5-terminal switch, but Revisit™ has reintroduced it with this aftermarket reissue.     Has 5 electrical terminals on back of switch.   1/4" push-on terminals, or solder directly to terminals.   Rated 20A @ 125VAC, 16A @ 250VAC. 15/16" x 1 1/16" x 1" deep.  Internal neon lamp powered by 125VAC.   For newer JCM900 and JCM2000 series with 4 terminals on the power switch, see the SW-491 switch above.
Part #SW-492
$10.95  


Click on photo for
larger view
ROCKER SWITCH, LIGHTED POWER, ORIGINAL Marshall® , FOUND IN Marshall® JVM and JCM2000 SERIES   Used in the TSL100, TSL122, DSL100, DSL50, JVM410H, etc.  Has 4 electrical terminals on back of switch.   1/4" push-on terminals.   Rated 22A @ 125VAC. 15/16" x 1 1/16" x 1" deep.  Internal neon lamp powered by 120VAC.  Not for use on 230VAC.  Original Marshall part number B8C75184.
Part #SW-493
$8.95  


Click on photo for
larger view
ROCKER SWITCH, LIGHTED POWER, RED.
Has 4 electrical terminals on back of switch.   1/4" push-on terminals, or solder directly to terminals.   Rated 20A @ 125VAC, 16A @ 250VAC.   Needs rectangular cutout of 0.82" wide x 1.15" tall (21mm x 29mm).   Internal neon lamp powered by either 125VAC or 250VAC.    Excellent cost-effective replacement for the power switch on the Marshall TSL100, TSL122, DSL100, DSL50, JVM410H, etc.   Original Marshall switch does not have the "1" and "0" on and off markings, but otherwise is nearly identical.   Also used on many Engl Amp models.   Replacement for the discontinued Fender part numbers 0064049000 and 0064050000, used in the Bassman 250 and the Bassman 100 (the version with a white control panel only).  Also replaces the # 700048-3159 power switch in most models of Furman power conditioners.  Replaces American DJ part # Z-PDP/900-PS-N for use in the American DJ PC-100A PC-4 power centers.
Part #SW-5075
$4.95  


Click on photo for
larger view
ROCKER SWITCH, BLACK, USED AS STANDBY SWITCH IN Marshall® JCM SERIES & OTHERS  
Has 4 electrical terminals on back of switch.   1/4" push-on terminals, or solder directly to terminals.   15/16" x 1 1/16" x 1" deep.
Part #SW-490
$7.95  


Click on photo for
larger view
SAVE WITH MULTIPACK!  THIS SET CONTAINS BOTH THE POWER AND THE STANDBY ROCKER SWITCHES, USED IN Marshall® JCM SERIES & OTHERS  
Lighted power switch has 4 electrical terminals on back of switch.   1/4" push-on terminals, or solder directly to terminals.   Rated 22A @ 125VAC, 16A @ 250VAC. 15/16" x 1 1/16" x 1" deep.  Internal neon lamp powered by either 125VAC or 250VAC.  Standby switch has 4 electrical terminals on back of switch.   1/4" push-on terminals, or solder directly to terminals.   15/16" x 1 1/16" x 1" deep.  Does your old Marshall® power switch have five terminals?  Click here to learn how to modify the wiring so that you may use the the power  switch in this set.
Part #SW-4901
$11.99  


Click on photo for
larger view
ORIGINAL Marshall® MINI ROCKER SWITCH FOR Marshall® MG SERIES - MARKED 0-1 FOR ON/OFF
DPDT Mini Rocker Switch.  Has 4 electrical terminals on back of switch.   Face of switch marked with "0" and "1" for on/off.   Original Marshall®  replacement.   0.51" x 0.76" mounting hole diameter, 10A-125 VAC, 6A-250VAC, DPST with .187" tabs.   To upgrade to a red lighted switch, see the SW-489L below.
Part #SW-489
$3.95  


Click on photo for
larger view
ORIGINAL Marshall® MINI ROCKER SWITCH FOR Marshall® MG SERIES - LIGHTED
DPDT Mini Rocker Switch with internal light.  Has 4 electrical terminals on back of switch.   Red lighted version - easier to see than the tiny LED Marshall® originally provided as a power-on light.    0.51" x 0.76" mounting hole diameter, 10A-125 VAC, 6A-250VAC, DPST with .187" tabs.    To ensure that the light works properly, make sure that the terminals directly behind the "1" on the rocker portion feed the power transformer, while the terminals behind the "0" are connected to the incoming power source.  
Part #SW-489L
$3.99  


Click on photo for
larger view
ORIGINAL Marshall® PUSH SWITCH
DPDT Mini Short-Throw Push Switch.  Has 6 electrical terminals on bottom of switch (DPDT).  Used for channel switching, FX switching on the front panels of many Marshall® amps from the 1990s.    Found in the JMP-1 preamp, 6100 Anniversary, JFX-1 Signal Processor, and early 90s Valvestate MK1 models: VS100R, VS100RH, 8010, 8020, 8040, 8080, 8100, 8200, 8240, 8280.   Original Marshall® part number S212.   For switch cap, see the K-212 or K-213, depending on the amp model.
Part #SW-212
$4.25  


Click on photo for
larger view
ORIGINAL Marshall® , VOX, AND Blackstar® PUSH SWITCH
DPDT Mini Short-Throw Push Switch.  Has 6 electrical terminals on bottom of switch (DPDT).  Used for channel switching (and FDD) on Marshall® MG Series such as the MG15DFX, MG30DFX, MG50DFX, MG100DFX, MG250DFX.   Used in the Vox® Pathfinder, V9168R,  with Reverb.  Vox® part number V3650 and V904530002.   Used in most Blackstar® Amps as SW2; also on back PCB: SW1; SW2; and SW3.  Blackstar® part number MCSWH02002.   Also found in other brands of amplifiers. 
Part #SW-650
$3.95  


Click on photo for
larger view
ORIGINAL ILLUMINATED Marshall® PUSH SWITCH
4PDT Mini Short-Throw Push Switch.  Has 14 electrical terminals on bottom of switch (4PDT + LED).   Contains red LED which illuminates through the stem of the switch.   Used for channel switching on certain amp models from the JCM900 series, including the 4100, 4101, 4102, 4500, 4501 and 4502.   Original Marshall® part number S206.  Does NOT include the clear switch cap - reuse existing cap.
Part #SW-206
$6.95  


Click on photo for
larger view
SQUARE SWITCH CAP - FITS SW-212
This is a black 5mm x 5mm (approx 3/16") square mini-switch cap which fits the SW-212 Marshall® Push Switch (used primarily for channel switching).  Replaces the original S213 switch cap from Marshall® , which has now been discontinued.   NOTE:   This is NOT the power switch cap on ValveState Amps.   This square cap is found on the Marshall®, 6100, 6101, JMP1, JCM600, JCM602, JTM310, JTM312, JTM610, JTM612, JTM615, JTM622, 8010, AS80R, 8010, 8020, 8040, 8080, 8100, 8200, 8240, 8280, and 9004 models.

Part #K-213
$1.50  


Click on photo for
larger view
ROUND SWITCH CAP - FITS SW-212
This is a black 5mm (approx 3/16") diameter X 9mm long switch cap which fits the SW-212 Push Switch.    The diameter of this switch cap is smaller than the original round switch cap from Marshall® found on some of the early ValveState models.  Does NOT fit the TSL/DSL amps in the JCM2000 series.

Part #K-212
$1.50  


Click on photo for
larger view
Marshall® VINTAGE STYLE IMPEDANCE SELECTOR PLUG
This male plug insert fits the speaker impedance selector socket on many vintage Marshall® amps from 25+ years ago.  Frequently lost because it was removable from the rear of the amp.

Part #P-502
$9.95  


Click on photo for
larger view
Marshall® Impedance Selector for Reissue Series.  Marshall® Impedance Selector for Reissue Serie, used in 1959, 1987, 2203, 2245 etc. Fits also Kerry King and Randy Rhoads models!  Needs 30mm hole, Mounting: 38mm. 
Part #MS-416

$24.99


Click on photo for
larger view
Marshall® Impedance/Mode Selector switch.  Correct replacement for PCB mount impedance and high-low (pentode-triode) mode switch found on the back of many Marshall® JCM900 and JCM2000 series amplifiers.  Also used as the impedance switch in Marshall® 4x12 Cabinets (such as the 1960 series cabinets).    Found in other British-made amplifiers and cabinets as well.  Marshall® part number S208.
Part #SW-4500
$7.95  


Click on photo for
larger view
SWITCH, CARLING SPST TOGGLE, ORIGINAL REPLACEMENT FOR 60's and 70's Fender® AMPS (POWER & STANDBY SWITCHES)
Part #SW-495
$4.95  


Click on photo for
larger view
SWITCH, STANDARD SIZE TOGGLE - Rated at 20 Amps (125VAC) or 15 Amps (250VAC).   Fits 1/2" chassis hole.   Solder terminals or 1/4" push on, single pole / single throw (SPST).   Two position - on/off. NOTE:   RATED FOR AC SERVICE ONLY - NOT RECOMMENDED FOR USE AS A GUITAR AMPLIFIER STANDBY SWITCH
Part #STS-20
$3.95  


Click on photo for
larger view
SWITCH, STANDARD SIZE TOGGLE - Made by Carling - rated at 15A, 125VAC. Two position (on/off), double pole (DPST). Fits 1/2" chassis hole. Solder terminals or 1/4" push-on.
Part #SW-525
$6.95  


Click on photo for
larger view
SWITCH, STANDARD SIZE TOGGLE - Made by Carling - rated at 15A, 125VAC. Two position (on/off), single pole (SPST). Fits 1/2" chassis hole. Solder terminals.
Part #SW-526
$4.95  


Click on photo for
larger view
SWITCH, STANDARD SIZE TOGGLE - RATED AT 10 Amps (125VAC) or 6 Amps (250VAC) - TWO POSITION (ON/ON).   Fits 1/2" chassis hole.   Screw terminals, or remove screws for soldered connections.    Double-pole double-throw, no center off - two positions (ON/ON).
Part #STS-15-DPDT
$5.95  


Click on photo for
larger view
SWITCH, STANDARD SIZE TOGGLE - RATED AT 15 Amps (125VAC) or 10 Amps (250VAC) - THREE POSITION (ON/OFF/ON).   Fits 1/2" chassis hole.   Screw terminals, or remove screws for soldered connections.    Double-pole double-throw, with center off - three positions (ON/OFF/ON).
Part #STS-15-DPDT-CO
$6.50  


Click on photo for
larger view
FOOT SWITCH, CARLING BRAND, SPDT, LATCHING
Found in many type of footswitches.  Has 3 electrical terminals (single pole, double throw)Solder lugs for wire.
Part #FS-492
$9.95  


Click on photo for
larger view
FOOT SWITCH, CARLING BRAND, SPST, LATCHING, REPLACEMENT FOR Fender®, ETC.
Carling SPST footswitch. Used in Marshall® etc. Reverb/tremolo/channel switching pedals.  Has 2 electrical terminals (single pole, single throw)Solder lugs for wire.
Part #FS-493
$9.95  


Click on photo for
larger view
FOOT SWITCH, SPDT, LATCHING, FOR SWITCHING AND EFFECTS - Marshall® TYPE.
Has 3 electrical terminals (single pole, double throw).   Solder lugs for wire. Commonly found in Marshall® footswitch boxes, as well as other brands.
Part #FS-398
$3.95  


Click on photo for
larger view
FOOT SWITCH, SPDT, LATCHING, PC MOUNT, FOR SWITCHING AND EFFECTS - Marshall® TYPE
Electrically equivalent and physically the same body size as the FS-398, but made for direct connection to a PC board.  Found in the some Marshall® footswitch boxes with PC board design. Has 3 electrical terminals (single pole, double throw).  
Part #FS-398-PC
$3.95  


Click on photo for
larger view
FOOT SWITCH, DPDT, MOMENTARY, FOR SWITCHING AND EFFECTS.
Made for switching and effects units which require a momentary connection rather than a "hard" connection (no "click").  PC terminals.   Used in the 5-way foot controller on the Marshall® TSL-100 amps.    Marshall® Part number SWTP-00047.   Also fits some Blackstar® HT Dual Footpedals.    Blackstar® part #MCSWH02014.  Note:   With momentary PC Mount switches, it is necessary to check the pins with a meter and determine the normally open and normally closed pins, comparing to the original switch and design before installing.  Otherwise, it is possible to install a momentary switch "backwards" (reversed 180 degrees) and the device will not work properly.
Part #FS-503-PC
$3.95  


Click on photo for
larger view
FOOT SWITCH, DPDT, LATCHING, PC MOUNT, FOR SWITCHING AND EFFECTS.
Double-pole Double-Throw, made for direct connection to a PC board.  Has 6 electrical terminals.

Part #FS-498-PC

(Also see our complete line of switches)
$3.95  


Click on photo for
larger view
FOOT SWITCH, ALPHA MINIATURE DPDT, LATCHING, PC MOUNT, FOR SWITCHING AND EFFECTS. 
Smaller body than the FS-498-PC, this switch is used in many stomp boxes.  The physical size of the pushbutton is the same as all of the other switches - only the rectangular body of the switch is smaller for more compact spaces.  This is a "firm-click" switch - not a momentary.   Switch is marked "L" on the side (for locking).  This is a shorter version than used in MXR pedals - will not fit MXR!    Order the D-ECB554 for MXR pedals.
Part #FS-211-PC
$6.95  


Click on photo for
larger view
FOOT SWITCH, ALPHA DPDT, LATCHING, SOLDER LUGS, FOR SWITCHING AND EFFECTS. 
This switch is the same as the FS-211-PC, except it has solder lugs for wire attachment.   Made for effects boxes that do not have a PC board under the footswitch.  The physical size of the pushbutton is the same as all of the other switches - only the rectangular body of the switch is smaller for more compact spaces.  This is a "firm-click" switch - not a momentary.   Switch is marked "L" on the side (for locking).
Part #FS-211
$6.95  


Click on photo for
larger view
FOOT SWITCH, ALPHA DPDT, MOMENTARY, PC MOUNT, FOR SWITCHING AND EFFECTS. 
This switch is the same as the FS-211-PC, except it is momentary (no firm 'click') for those pedals which require a momentary switch.  Switch is marked "M" on the side for momentary.   Pins for PC board mounting.  The physical size of the pushbutton is the same as all of the other switches - only the rectangular body of the switch is smaller for more compact spaces.  Note:   With momentary PC Mount switches, it is necessary to check the pins with a meter and determine the normally open and normally closed pins, comparing to the original switch and design before installing.  Otherwise, it is possible to install a momentary switch "backwards" (reversed 180 degrees) and the device will not work properly.

Part #FS-211-PC-M
$6.95  


Click on photo for
larger view
FOOT SWITCH, ALPHA DPDT, MOMENTARY, SOLDER LUGS, FOR SWITCHING AND EFFECTS. 
This switch is the same as the FS-211-PC-M, except it has solder lugs for wire attachment.  This switch is momentary (no firm 'click') for those pedals which require a momentary switch.  Switch is marked "M" on the side for momentary.    Made for effects boxes that do not have a PC board under the footswitch.  The physical size of the pushbutton is the same as all of the other switches - only the rectangular body of the switch is smaller for more compact spaces.  Note:   With momentary switches, it is necessary to check the pins with a meter and determine the normally open and normally closed pins, comparing to the original switch and design before wiring.  Otherwise, it is possible to install a momentary switch "backwards" (reversed 180 degrees) and the device will not work properly.
Part #FS-211-M
$6.95  


Strat®, Stratocaster®, Esquire®, Telecaster®, Tele®, Jazzmaster®, Jaguar®, Mustang®, P.Bass®, J.Bass® and Fender® are registered trademarks of Fender® Musical Instruments. The replacement necks and bodies are for a Fender® or Squier® by Fender® guitar or bass. The distinctive headstock designs and the distinctive body designs of the Stratocaster®, Telecaster®, J.Bass®, P.Bass® and Tele® Bass are registered trademarks of Fender® Musical Instruments Co.  
Peavey® is a registered trademark of Peavey® Electronics Corporation.
Marshall® is a registered trademark of Marshall® Amplification Plc.
Mesa Boogie® is a registered trademark of MESA/Boogie® Ltd.
AmpRepairParts.com and Studio Sound Electronics are not affiliated with these companies.
All company names, logos and product names mentioned on these pages are trademarks of their respective owners.

Copyright ©2017 Studio Sound Electronics - All Rights Reserved
Not responsible for web site errors or omissions