|
Mesa/Boogie Hardware
(Also see our complete line of hardware) |
|
|

Click on photo for
larger view |
10-Conductor Ribbon Cable 3"
Used to interconnect circuit boards in a variety of amps.
• 3 inches long
• 10 conductors set at 0.1 inch spacing -
complete cable is 1 inch wide
• Bare wire termination for soldering to PC board at 0.1" hole spacing - no connectors
• May be easily cut with an X-Acto knife to make a cable of fewer than 10
conductors.
• Not recommended for use in the Fender Hot Rod Deluxe /
Deville or Blues Deluxe / Deville. The ribbon cables used in
those amps have ribbon cables with conductors set at 0.156" spacing - this cable
is too narrow for that application.
Part #RJ-310 |
$0.99 |
|

Click on photo for
larger view |
TUBE RETAINER WITH GRIP TEETH, DESIGNED FOR OCTAL TUBES WITH PHENOLIC BASE SUCH AS 6L6 OR EL34.
Used in Mesa-Boogie® and many other amps. 1 1/2"
mounting centers. Made by Belton.
Part #TC-142 |
$1.95
|
|

Click on photo for
larger view |
TUBE SHIELD, BAYONET "PUSH AND TWIST" TYPE, ALUMINUM, 1 15/16" TALL.
Includes new base, if needed. Spring in top of shield which fits over the
tube. Fits 12AX7A and similarly sized preamp tubes. Replacement for Fender® and many other brands. Holes in base spaced 1 1/8" apart.
Part #TS-325S |
$1.95 |
|

Click on photo for
larger view |
TUBE SHIELD, BAYONET "PUSH AND TWIST" TYPE, ALUMINUM, 1 15/16" TALL,
SET OF 6.
Includes new bases, if needed. Spring in top of shield fits over the tube.
Fits 12AX7A and similarly sized preamp tubes. Replacement for Fender® and many
other brands. Holes in base spaced 1 1/8" apart.
Part #TS-325S-6 |
$8.95 |
|

Click on photo for
larger view |
Ground Connection Terminals - Flat
Used to connect a ground wire to a screw and nut on a chassis. Flat,
with one hole for wire.
With built-in lock washer to keep the screw and nut from loosening.
Designed for a #8 size screw. Pack of 10 terminals.
Part #2310915 |
$1.99
(Pack of 10 terminals)
|
|

Click on photo for
larger view |
TERMINAL STRIPS, 6 LUG, SET OF
2. Perfect for amplifier circuit additions or modifications.
End terminals on each strip are the mounting lugs, so they become a ground lug
if attached to a metal chassis. Each terminal strip is 2 1/4 inches
long. The lugs are set on 3/8 inch centers. Each lug
will accept wires up to 16ga - smaller gauge allows multiple wires to be
connected to each lug. Set contains 2 terminal strips as pictured.
Mounting hardware not included.
Part #2320822 |
$2.89
(for a set of 2 terminal strips) |
|

Click on photo for
larger view |
CUP WASHER, BLACK METAL, PACK OF 10. USED WITH #8 BLACK SCREW ON AMP AND SPEAKER CABINETS.
Part #BCW-10 |
$1.29
(pack of 10) |
|

Click on photo for
larger view |
SPEAKER BAFFLE MOUNTING SCREW WITH BOTH WOOD AND MACHINE THREADS, SET OF 4. Locking
nut and washer included. Phillips head. Drill hole, insert and
tighten screws into wood from front of baffle. Install grill cloth, and
you have professional speaker mounting studs. Replacement for
original Fender® speaker mounting studs. Set of 4.
Part #SC-409-4 |
$2.29
(For a pack of 4 screws with nuts and lock washers) |
|

Click on photo for
larger view |
ISOLATION WASHER - 3/8"
3/8" outside diameter neoprene bonded flat washer. Perfect for
bolting speakers to cabinets. It will securely hold the speaker in place and
stop any rattling. For use with #6 and #8 screws. Set of 4 washers.
Part #SIW-38-4 |
$0.59
(For a set of 4 washers) |
|

Click on photo for
larger view |
BLACK PAN-HEAD WOOD SCREWS, #6 X 3/4", PACK OF 10. Deep
threads, sharp point, pan head with Philips drive. #6 screw, 3/4 inch
long, pack of 10.
Part #SCR-435 |
$0.79
(pack of 10) |
|
 |
BLACK PAN-HEAD WOOD SCREWS, #8 X 1/2", PACK OF 10. Deep
threads, sharp point, pan head with Philips drive. #8 screw, 1/2 inch
long, pack of 10.
Part #BWS8-5 |
$0.89
(pack of 10) |
|
 |
BLACK PAN-HEAD WOOD SCREWS, #8 X 3/4", PACK OF 10. Deep
threads, sharp point, pan head with Philips drive. #8 screw, 3/4 inch
long, pack of 10.
Part #BWS8-75 |
$0.95
(pack of 10) |
|
 |
BLACK PAN-HEAD WOOD SCREWS, #8 X 1", PACK OF 10. Deep
threads, sharp point, pan head with Philips drive. #8 screw, 1 inch long,
pack of 10.
Part #BWS8-1 |
$1.05
(pack of 10) |
|
 |
BLACK PAN-HEAD WOOD SCREWS, #8 X 1 1/2", PACK OF 10.
Deep threads, sharp point, pan head with Philips drive. #8 screw, 1-1/2
inches long, pack of 10.
Part #BWS8-15 |
$1.19
(pack of 10) |
|

Click on photo for
larger view |
SMALL BLACK RUBBER FEET, PACK OF 4. 3/4" DIAMETER AT TOP, 5/8" DIAMETER AT BOTTOM, 5/16" TALL. BLACK RUBBER WITH METAL INSERT. USED TO SUPPORT EFFECTS, SMALLER AMPS, SMALLER MIXERS.
SCREWS NOT INCLUDED.
Part #BRF-4 |
$2.95
(pack of 4) |
|

Click on photo for
larger view |
SMALL BLACK RUBBER FEET, SET OF 4.
This heavy-duty rubber foot offers a sure grip
on all types of surfaces. Ideal for smaller amps, amp heads, or speaker
cabinets. The integral metal washer in the mounting hole helps prevent
mounting screw "break-through" and adds overall durability.
Just under 1 inch - 15/16"
diameter at the top, rounded down to 5/8" diameter at the bottom, and 3/8"
tall. Screws not included. Set of 4
feet.
Part #BRF-723
|
$3.95
(pack of 4) |
|

Click on photo for
larger view |
MEDIUM BLACK RUBBER FEET, SET OF 4.
This heavy-duty rubber foot offers a sure grip
on all types of surfaces. Ideal for large rack cabinets or speaker cabinets.
The integral metal washer in the mounting hole helps prevent mounting screw
"break-through" and adds overall durability. 1" diameter x 1" tall. Mounting
screws not included.
Part #BRF-1691
|
$4.95
(pack of 4) |
|

Click on photo for
larger view |
MEDIUM BLACK RUBBER FEET, SET OF 4.
This heavy-duty rubber foot offers a sure grip
on all types of surfaces. Ideal for amp heads, combo amps, or smaller speaker cabinets.
The integral metal washer in the mounting hole helps prevent mounting screw
"break-through" and adds overall durability. 1" diameter x
5/8" tall. Mounting
screws not included.
Part #BRF-1692
|
$4.95
(pack of 4) |
|

Click on photo for
larger view |
MEDIUM BLACK RUBBER FEET, SET OF 4.
TAPERED -1 3/16" DIAMETER AT SMALL END, 1 1/4" DIAMETER AT LARGE END. 1/2" TALL. BLACK RUBBER WITH METAL INSERT. USED TO SUPPORT EFFECTS, AMPS, MIXERS.
MOUNTING SCREWS NOT INCLUDED.
Part #BRF-9112 |
$4.95
(pack of 4) |
|

Click on photo for
larger view |
X-LARGE BLACK RUBBER FEET, SET OF 4. TAPERED - 1 5/8" DIAMETER AT
LARGE END, 1 1/4" AT SMALL END. 3/4" TALL. BLACK RUBBER WITH METAL INSERT. USED TO SUPPORT AMP HEADS, SPEAKER CABINETS.
MOUNTING SCREWS NOT INCLUDED.
Part #BRF-9107 |
$7.95
(pack of 4) |
|

Click on photo for
larger view |
Fender® Style Flat Mount 2" Caster Wheels - Set
of 4.
Great for Fender® and many other brands of amps or cabinets. Each
wheel capable of supporting 45 lbs, or 180 lbs total for the set of 4.
Wheels 2" in diameter. Specifications found
here. Note:
Mounting screws NOT included.
Part #FCW-4F |
$24.95
(Set of 4 casters)NOT
SOLD OUTSIDE THE USA
|
|

Click on photo for
larger view |
Fender® Style Pop-Out 2" Caster Wheels - Set
of 4.
Great for Fender® and many other brands of amps or cabinets. Each
wheel capable
of
supporting 45 lbs, or 180 lbs total for the set of 4. Wheels 2" in
diameter. The same type of removable caster wheels used on Fender® amps
since the 1960s. Note:
Mounting screws NOT included. Must drill 5/8" hole in bottom of
cabinet to accomodate post for wheel.
Part #FCW-4R |
$28.95
(Set of 4 pop-out casters)
NOT SOLD OUTSIDE THE USA
|
|

Click on photo for
larger view |
Revisit™ AMP HANDLE, VINTAGE LEATHER-LOOK STYLE, BLACK WITH
BLACK STITCHING
Good replacement for Ampeg, Mesa Boogie, Randall®, Bogner, Ashdown, Rivera,
Blackstar, many others. Handle
length is 8 9/16 inches (8.57"), center-to-center mounting distance is 7 3/8
inches (7.38") Black with black stitching, nickel mounts.
More details Mounting
screws not included - use SC-402 screw pack.
Part #AH-281 |
$11.95 |
|

Click on photo for
larger view |
Revisit™ AMP HANDLE, VINTAGE LEATHER-LOOK STYLE, DARK BROWN WITH
BROWN STITCHING
Good replacement for Ampeg, Mesa Boogie, Randall®, Bogner, Ashdown, Rivera,
Blackstar, many others. Handle
length is 8 9/16 inches (8.57"), center-to-center mounting distance is 7 3/8
inches (7.38") Dark brown with brown stitching, nickel mounts.
More details Mounting
screws not included - use SC-402 screw pack.
Part #AH-270 |
$11.95 |
|

Click on photo for
larger view |
Revisit™ AMP HANDLE, VINTAGE LEATHER-LOOK STYLE, DARK BROWN WITH
WHITE STITCHING
Good replacement for Ampeg, Mesa Boogie, Randall®, Bogner, Ashdown, Rivera,
Blackstar, many others. Handle
length is 8 9/16 inches (8.57"), center-to-center mounting distance is 7 3/8
inches (7.38") Dark brown with white stitching, nickel mounts.
More details Mounting
screws not included - use SC-402 screw pack.
Part #AH-318 |
$11.95 |
|

Click on photo for
larger view |
Revisit™ AMP HANDLE, VINTAGE LEATHER-LOOK STYLE, DEEP NAVY BLUE-GREY WITH
WHITE STITCHING
Good replacement for Ampeg, Mesa Boogie, Randall®, Bogner, Ashdown, Rivera,
Blackstar, many others. Handle
length is 8 9/16 inches (8.57"), center-to-center mounting distance is 7 3/8
inches (7.38") Dark navy blue-grey with white stitching, nickel mounts.
More details Mounting
screws not included - use SC-402 screw pack.
Part #AH-319 |
$11.95 |
|


Click on photo for
larger view |
Revisit™ BLACK GUITAR AMP HANDLE,
WITH HARDWARE.
Rugged rubber black handle strap, steel reinforced. Black metal caps.
Black 10-32 screws and T-Nut mounting hardware are included. Handle strap is 7/8"
wide. Designed for screw holes set 8 1/4 to 8 3/8 inches apart. Total length of handle when properly mounted is
10 1/4".
Part #GAH-271B |
$7.99 |
|


Click on photo for
larger view |
Revisit™ GUITAR AMP HANDLE
- BLACK.
Rugged rubber black handle strap, steel reinforced. Black metal caps. Screws not included - recommend using
our SC-403B Black 10-32 type screws along with a 10-32 T-Nut for secure mounting. Handle strap is 7/8"
wide. Designed for screw holes set 8 1/4 inches apart. Total length of handle when properly mounted is
10 1/4".
Part #GAH-1 |
$6.99 |
|

Click on photo for
larger view |
BLACK HANDLE SCREWS
Pack of 2 stainless-steel handle screws finished
in satin black for use
with black end-cap handles, such as our GAH-1 or GAH-271B. 1" Long, 10-32 threads, finished in satin black to match black end caps. Designed
to work with a 10-32 T-Nut, in cabinet wood of 3/4" or less.
Will not work with external nut - must be a T-Nut. Will not work
with cabinet wood thicker than 3/4".
See Data Sheet here
Part #SC-403B |
$0.99
(for a pack of 2 screws) |
|


Click on photo for
larger view |
Revisit™ CHROME/BLACK GUITAR AMP HANDLE
- CHROME, WITH HARDWARE.
Rugged rubber black handle strap, steel reinforced. Chrome metal caps.
10-32 screws and T-Nut mounting hardware are included. Handle strap is 7/8"
wide. Designed for screw holes set 8 1/4 inches apart. Total length of handle when properly mounted is
10 1/4".
Not recommended for Fender, as the screws are set too far apart for
Fender® amp specifications.
Part #GAH-271C |
$7.99 |
|

Click on photo for
larger view |
HANDLE SCREWS
Pack of 2 stainless steel handle screws for
GAH-271C Handle. 1" Long, 10-32 threads. Designed
to work with a 10-32 T-Nut, in cabinet wood of 3/4" or less.
Will not work with external nut - must be a T-Nut. Will not work
with cabinet wood thicker than 3/4".
See Data Sheet here
Part #SC-403 |
$0.99
(for a pack of 2 screws) |
|

RED
Click on photo for
larger view |
REPLACEMENT PILOT LAMP JEWEL, Fender®, Peavey®, Mesa Boogie®, MANY
OTHERS. RED.
Part #JL-115R |
$2.99 |
|

VIOLET
Click on photo for
larger view |
REPLACEMENT PILOT LAMP JEWEL, Fender®, Peavey®, Mesa Boogie®, MANY
OTHERS. Violet - just plain cool!
NOTE: When illuminated by the bulb, this
violet jewel tends to have a hue slanted toward the red spectrum, so some call
the look a reddish-pinkish-violet color. If you like violet/purple
and want it toward the warmer end of the color spectrum, this is the jewel for
you. If you like it more bluish - toward the cooler end of the
violet color zone, choose the purple jewel JL-115P below instead.
Part #JL-115V |
$2.99 |
|

PURPLE
Click on photo for
larger view |
REPLACEMENT PILOT LAMP JEWEL, Fender®, Peavey®, Mesa Boogie®, MANY
OTHERS. Purple - just plain cool! Fender® part number 0990953000.
NOTE: To the naked eye, this jewel looks
blue until you put it in front of the P-47 bulb. The bulb has an
amber tint to it, so the combo makes the jewel glow purple. When
illuminated by the bulb, this purple jewel tends to have a hue slanted toward
the blue spectrum, so some call the look a bluish-purple color. If
you like violet/purple and want it toward the cooler end of the color spectrum,
this is the jewel for you. If you like it more reddish - toward the
warmer end of the violet color zone, choose the violet jewel JL-115V above instead.
Part #JL-115P |
$2.99 |
|

AMBER
Click on photo for
larger view |
REPLACEMENT PILOT LAMP JEWEL, Fender®, Peavey®, Mesa Boogie®, MANY
OTHERS. AMBER.
Part #JL-115A |
$2.99 |
|

GREEN
Click on photo for
larger view |
REPLACEMENT PILOT LAMP JEWEL, Fender®, Peavey®, Mesa Boogie®, MANY
OTHERS. GREEN.
Part #JL-115G |
$2.99 |
|

BLUE
Click on photo for
larger view |
REPLACEMENT PILOT LAMP JEWEL, Fender®, Peavey®, Mesa Boogie®, MANY
OTHERS. BLUE. NOTE: Due to
the orange glow of the bulb normally used behind this jewel, the resulting color
is not a pure brilliant blue ... head on, it looks like a somewhat washed-out
blue, and from a side angle, it looks more like purple. This is not
the fault of the jewel, but rather the combination of the blue color of the
jewel combined with the orange glow of the bulb. If used with a pure white
light (such as a white LED), the resulting look is a deep blue color.
Part #JL-115B |
$2.99 |
|

CLEAR
Click on photo for
larger view |
REPLACEMENT PILOT LAMP JEWEL, Fender®, Peavey®, Mesa Boogie®, MANY
OTHERS. CLEAR.
Part #JL-115C |
$2.99 |
|

WHITE
Click on photo for
larger view |
REPLACEMENT PILOT LAMP JEWEL, Fender®, Peavey®, Mesa Boogie®, MANY
OTHERS. WHITE.
Part #JL-115W |
$2.99 |
|

Click on photo for
larger view |
REPLACEMENT PILOT LAMP JEWEL KIT, Fender®, Peavey®, Mesa Boogie®, many
others. Kit of 6 jewels - change your light color as often as you
like. Contains one each red, amber, green, blue, violet and clear.
Part #JLK-115 |
$12.99 |
|

Click on photo for
larger view |
PILOT LAMP HOLDER, REPLACEMENT FOR MANY BRANDS.
Lamp holder. Relampable front panel indicator accepts a variety of T-2 and T-3 1/4 miniature bayonet lamps. 11/16" chassis hole. Accepts all of the colored jewels on this page.
Total Length = 1.755" (solder lugs included in measurement) (extends about 1.68" from front of panel to end of solder lugs) Rating: 125V, 75W
Part #LH-110 |
$5.49 |
|

RED
Click on photo for
larger view |
PREMIUM PILOT LAMP ASSEMBLY, RED, REPLACEMENT FOR
MESA BOOGIE, FENDER®
AND OTHER AMP BRANDS
Complete pilot lamp assembly:
Includes premium pilot lamp holder,
red jewel and #47 bulb complete, fits 11/16" chassis hole.
Designed for 6.3 volts (filament voltage in tube amps). Ready for installation and wiring.
Part #FLA-110R |
$7.95 |
|

AMBER
Click on photo for
larger view |
PREMIUM PILOT LAMP ASSEMBLY,
AMBER, REPLACEMENT FOR MESA BOOGIE, FENDER®
AND OTHER AMP BRANDS
Complete pilot lamp assembly:
Includes premium pilot lamp holder,
amber jewel and #47 bulb complete, fits 11/16" chassis hole.
Designed for 6.3 volts (filament voltage in tube amps). Ready for installation and wiring.
Part #FLA-110A |
$7.95 |
|

BLUE
Click on photo for
larger view |
PREMIUM PILOT LAMP ASSEMBLY,
BLUE, REPLACEMENT FOR MESA BOOGIE, FENDER®
AND OTHER AMP BRANDS
Complete pilot lamp assembly:
Includes premium pilot lamp holder,
blue jewel and #47 bulb complete, fits 11/16" chassis hole.
Designed for 6.3 volts (filament voltage in tube amps). Ready for installation and wiring.
NOTE: Due to the orange glow of the #47 bulb
used behind this jewel, the resulting color is not a pure brilliant blue ...
head on, it looks like a somewhat washed-out blue, and from a side angle, it
looks more like purple. This is not the fault of the jewel, but
rather the combination of the blue color of the jewel combined with the orange
glow of the bulb. If used with a pure white light (such as a white LED),
the resulting look is a deep blue color.
Part #FLA-110B |
$7.95 |
|

GREEN
Click on photo for
larger view |
PREMIUM PILOT LAMP ASSEMBLY,
GREEN, REPLACEMENT FOR MESA BOOGIE, FENDER®
AND OTHER AMP BRANDS
Complete pilot lamp assembly:
Includes premium pilot lamp holder,
green jewel and #47 bulb complete, fits 11/16" chassis hole.
Designed for 6.3 volts (filament voltage in tube amps). Ready for installation and wiring.
Part #FLA-110G |
$7.95 |
|

Click on photo for
larger view |
INDICATOR LAMP, #47, T-3-1/4, 6.3V, .15 AMP, BAYONET BASE
P-47
Long life general replacement lamps for dials, indicators, etc. Sold individually.
Part #P-47 |
$0.99 |
|

Click on photo for
larger view |
Revisit™
VTL5C1 OPTO-ISOLATOR
Replaces VTL5C1 from Vactec or Excelitas at an
affordable price. Used in many Mesa-Boogie and Crate models in the channel
switching circuit. 100dB dynamic range, fast response (2.5ms
turn-on), very high dark resistance (50 M Ohm). Light resistance 200 Ohms
at 20mA LED current. See datasheet here.
Part #VTL5C1 |
$4.95 |
|
|
Mesa/Boogie Jacks
(Also see our complete line of jacks) |
|
|

Click on photo for
larger view |
JACK, 1/4", MONO, OPEN CIRCUIT, WIRED, Switchcraft®
Found in many guitars, effects pedals, amps speaker output. Includes nut and washer.
Part #J-11 |
$2.25 |
|

Click on photo for
larger view |
JACK, 1/4", MONO, CLOSED CIRCUIT (SHORTING), WIRED, Switchcraft®
Found in vintage amps as the input jack. Includes nut and washer.
Part #J-12A |
$2.79 |
|

Click on photo for
larger view |
JACK, 1/4", MONO, CLOSED CIRCUIT
(SHORTING), WIRED, Switchcraft®, LONG BUSHING
Same as the J-12A jack, but with longer (3/8") threaded bushing for mounting in thicker panels. Includes nut and washer.
Part #J-L12A |
$2.99 |
|

Click on photo for
larger view |
JACK, 1/4", MONO,
TIP SHUNT, WIRED, Switchcraft®,
LONG BUSHING, ISOLATION WASHERS
Same as the Switchcraft L12A jack but
includes a set of isolation washers.
The
isolation washers keep the jack from making contact with your chassis. This
leaves the jack ungrounded which is needed in certain applications.
Commonly used in older Fender® Hot Rod Deluxe/Deville and Blues Deluxe/Deville
amps to
replace the fragile input jacks.
Part #J-L12AW |
$3.49 |
|

Click on photo for
larger view |
JACK, 1/4", TIP-RING-SLEEVE, OPEN CIRCUIT, WIRED, Switchcraft®
Used with T/R/S plugs for either balanced connections or stereo connections. Also very common in guitars with active pickups, and as the input jack on some effects pedals. The ring conductor is used in these cases to "turn on" the battery by tying one leg of the battery to ground via the plug.
Part #J-12B |
$2.99 |
|

Click on photo for
larger view |
JACK, 1/4", TIP-RING-SLEEVE, OPEN CIRCUIT, WIRED, Switchcraft®, LONG BUSHING
Same as the J-12B jack, but with longer (3/8") threaded bushing for mounting in thicker panels. Includes nut and washer.
Part #J-L12B |
$3.99 |
|

Click on photo for
larger view |
JACK, 1/4", TIP-SLEEVE, WITH ISOLATED SWITCHING. Switchcraft®
Used with for special switching applications - the two conductors for the switch are completely isolated from both the "hot" audio signal and the ground connection. Used in some Mesa/Boogie cabinets.
Part #J-13 |
$6.99
|
|

Click on photo for
larger view |
JACK, 1/4", TIP/RING/SLEEVE, WITH
TIP SHUNT. Switchcraft 13B Jack.
Tip/Ring/Sleeve
Switchcraft jack. Tip has a shunt contact, ring contact is open
circuit.
Part #J-13B |
$6.95 |
|

Click on photo for
larger view |
JACK, 1/4", MONO PC MOUNT PLASTIC, GENUINE CLIFF
UK
4 PC board terminals, switched. Used in many brands of amps and other equipment. With nut and washer.
Original Cliff UK part number CL1169.
Part #J-503 |
$1.99 |
|

Click on photo for
larger view |
SAVE WITH MULTIPACK! JACK, 1/4", MONO PC MOUNT PLASTIC,
GENUINE CLIFF UK,
PACK OF 6
4 PC board terminals, switched. Used in many brands of amps and other equipment.
Pack of 6 jacks, with nuts and washers. Original Cliff UK part number
CL1169.
Part #J-503-6 |
$9.99
(Set of 6 jacks) |
|

Click on photo for
larger view |
JACK,
1/4", MONO PC MOUNT PLASTIC, BRITISH STYLE WITH CHROME NUT AND CHROME TRIM RING
4 PC board terminals, switched. Used in newer Mesa Boogie amps, including
the Rosette, Mini Rectifier, Mark 5:Twenty-Five, etc.
Part #J-603 |
$2.29
(per jack) |
|

Click on photo for
larger view |
JACK, 1/4", STEREO INPUT, CLOSED CIRCUIT, PC MOUNT, GENUINE CLIFF
UK
Stereo input jack. 6 PC board terminals, switched. With nut and washer.
Original Cliff UK part number CL1227.
Part #J-504 |
$2.29 |
|

Click on photo for
larger view |
SAVE WITH MULTIPACK! JACK, 1/4", STEREO INPUT, CLOSED CIRCUIT, PC MOUNT,
GENUINE CLIFF UK,
PACK OF 6
Stereo input jack. 6 PC board terminals, switched. Pack of 6 jacks, with nuts and washers.
Original Cliff UK part number CL1227.
Part #J-504-6 |
$10.99
(Set of 6 jacks) |
|

Click on photo for
larger view |
SAVE WITH
OUR
MULTIPACK ASSORTMENT! THIS PACK CONTAINS THREE J-503 (4 PIN) AND THREE J-504 (6-PIN)
JACKS.
Many amps contain both the 4 pin and the 6 pin Cliff jacks. This
assortment gives you 3 of each jack ... Three J-503, and three J-504.
Original Cliff UK part numbers CL1169 and CL1227.
Part # J-5034-6 |
$10.49
(For 3 J-503 Jacks and 3 J-504 Jacks)
|
|

Click on photo for
larger view |
JACK,
1/4", STEREO PC MOUNT PLASTIC, BRITISH STYLE WITH CHROME NUT AND CHROME TRIM RING
6 PC board terminals, switched. Used in newer Mesa Boogie amps,
including the Rosette, Mini Rectifier, Mark 5:Twenty-Five, etc.
Part #J-604 |
$2.59
(per jack) |
|

Click on photo for
larger view |
JACK, 1/4", MONO PLASTIC,
GENUINE CLIFF UK, SOLDER TERMINALS, REPLACEMENT FOR Marshall®
4 solder terminals, switched. Used in "hand-wired" amps. With nut and washer.
Part #J-502 |
$2.99 |
|

Click on photo for
larger view |
JACK, 1/4", STEREO PLASTIC,
GENUINE CLIFF UK, SOLDER TERMINALS, REPLACEMENT FOR Marshall®
6 solder terminals, switched. Used in "hand-wired" amps. With nut and washer.
Part #J-505 |
$3.50 |
|

Click on photo for
larger view |
JACK NUT, PLASTIC,
GENUINE CLIFF UK, REPLACEMENT FOR Marshall® AND OTHERS.
Note: Replaces most black plastic jack nuts EXCEPT for
Roland. Will NOT fit Roland jacks.
Replacement jack nut as found on the J-502, J-503, J-504, J-505, J-503L and
J-504L jacks. Also fits the J-518 and J-519 jacks.
Part #J-5NT |
$0.50 |
|

Click on photo for
larger view |
JACK NUT MULTI-PACK - SAVE!
6 JACK NUTS, PLASTIC, GENUINE CLIFF UK, REPLACEMENT FOR Marshall® AND OTHERS.
Note: Replaces most black plastic jack nuts EXCEPT for
Roland. Will NOT fit Roland jacks.
Replacement jack nut as found on the J-502, J-503, J-504, J-505, J-503L and
J-504L jacks. Also fits the J-518 and J-519 jacks.
Part #J-5NT-6 |
$2.39 |
|
Click on photo for
larger view |
JACK, 1/4", PC MOUNT, STEREO, 5 PINS, SWITCHED, METAL BUSHING,
PC BOARD TYPE
Both tip and
ring conductors are switched (normally closed). 5 pins. Original Peavey® part number 31466217. Used in Peavey®, Mackie,
Mesa Boogie and other brands.
Replaces Switchcraft 114BPCX and 114BPCSX. Nut and washer on this jack
ARE included.
Part #J-529 |
$2.75 |
|

Click on photo for
larger view
Note:
Nut & Washer NOT included - reuse original, or order JNUT-38. |
|
JACK, 1/4", PC MOUNT, STEREO,
4 PINS, SWITCHED, METAL BUSHING.
Tip is switched
(normally
closed), ring conductor is not switched.
Made by Neutrik/Rean. Used in a variety of brands.
Replaces Switchcraft.
NUT & WASHER NOT INCLUDED - REUSE ORIGINAL OR ORDER JNUT-38, BELOW.
Part #J-524A |
$3.50 |
|

Click on photo for
larger view
Note:
Nut & Washer NOT included - reuse original, or order JNUT-38. |
|
JACK, 1/4", PC MOUNT, STEREO,
3 PINS, NON-SWITCHED, METAL BUSHING.
Three conductors (tip, ring and sleeve), 3 pins. No switching.
Made by Neutrik.
NUT & WASHER NOT INCLUDED - REUSE ORIGINAL OR ORDER JNUT-38, BELOW.
Part #J-234 |
$3.95 |
|
 |
JACK NUT AND WASHER, METAL,
SWITCHCRAFT®
Genuine Switchcraft® nut and washer set for the blackface/silverface Fender® bias pot, Mesa Boogie pots, and the
CTS or Alpha pots with 3/8" bushing (found on original vintage Fender®
blackface and silverface), as well as Peavey® and Switchcraft®
1/4" jacks. Does NOT fit the 24mm Marshall® pots.
Part #JNUT-38 |
$0.89
(Set of 1 washer and 1 nut) |
|

Click on photo for
larger view. Jack is in the picture to demonstrate how the washers
are installed - jack is NOT included with the washers. |
INSULATING SHOULDER WASHER, FIBER
Pair of fiber insulating shoulder washers for Switchcraft jacks with metal
bushings. Used to mount standard jacks in a 1/2" diameter chassis
hole, while insulating the metal bushing (ground) of the jack from the chassis.
ID 3/8", OD 1/2". Works great when replacing isolated plastic jacks with a
more durable metal jack, which is frequently done on the input jacks of the
Fender® Hot Rod Deville/Deluxe and Blues Deville/Deluxe. Two washers
are used on each jack, and the "shoulders" are placed facing each other through
the chassis. The washers not only isolate the ground of the jack
electrically for noise reduction, but also stabilize the jack in the 1/2"
diameter hole. Jack shown in picture NOT included. Works
well with the Switchcraft J-11, J-L11, J-12A, J-L12A, J-12B, J-L12B, J-13,
J-13A, J-112APC, J-112BX, J-114BX, J-521 and J-524 jacks.
Part #ISW-3069 |
$0.49
(For a pair of washers. Each jack needs two washers.) |
|

Click on photo for
larger view |
FAST-ON CONNECTOR JUMPER CABLES -
1/4 INCH TERMINALS 18 INCHES LONG
Teflon™ insulated silver plated copper jumpers, 18 gauge,
individual,
black and red. Terminated at each end in standard 1/4" speaker
fast-on connectors. (Note that many speakers use 3/16" terminals,
which are smaller than these connectors). May be used for internal
connections in many amplifiers (Marshall, Fender, etc) which use PC board
mounted 1/4" terminals. 18 inches (46 cm) long. Made in
USA. Each set contains one red and one black jumper.
Part #FJ-180 |
$1.59 |
|


Click on photo for
larger view |
Revisit™ SPEAKER HARNESS COMPLETE
WITH GENUINE SWITCHCRAFT #11 JACK and 24" SPEAKER WIRE FOR SINGLE SPEAKER.
Preassembled for speaker cabinets with one
speaker. Includes Switchcraft #11 jack,
and 24 inch Teflon™-insulated 18 ga speaker wire terminated in 3/16" push-on
speaker connectors. For two-speaker cabinets, see the SCH-2411X2,
below.
Part #SCH-2411 |
$8.99
|
|


Click on photo for
larger view |
Revisit™ SPEAKER HARNESS COMPLETE
WITH GENUINE SWITCHCRAFT #11 JACK and 24" SPEAKER WIRE FOR TWO SPEAKER
CABINET.
Preassembled for speaker cabinets with two
speakers in parallel. Includes Switchcraft #11 jack,
and 24 inch Teflon™-insulated 18 ga speaker wire terminated in 3/16" push-on
speaker connectors, plus an additional 24" jumper cable.
Part #SCH-2411X2 |
$14.99
|
|


Click on photo for
larger view |
Revisit™ SPEAKER HARNESS COMPLETE
WITH 1/4" STRAIGHT PLUG and 24" SPEAKER WIRE FOR SINGLE SPEAKER.
Preassembled for combo amps with one
speaker. Includes 1/4" straight plug,
and 24 inch Teflon™-insulated 18 ga speaker wire terminated in 3/16"
push-on speaker connectors. For 2-speaker cabinets, add the SJ-150 jumper,
below.
Part #SCH-224 |
$9.99
|
|


Click on photo for
larger view |
Revisit™
SPEAKER HARNESS, 2 ft LONG,
RIGHT-ANGLE PLUG TO BARE TINNED WIRE, 16 GAUGE CABLE
Replacement right-angle plug with 24" cable and stripped, tinned bare
wire.
Used to replace speaker cable in many combo amplifiers where the speakers are
connected to the amplifier chassis via a 1/4" jack and plug.
Heavy-duty 16ga round black speaker cable,
right-angle plug and bare wire ready for soldering to one
speaker.
Part #SCH-7090 |
$4.59 |
|


Click on photo for
larger view |
Revisit™
SPEAKER HARNESS, 2 ft LONG,
PUSH-ON TERMINALS, 16 GAUGE CABLE
Replacement right-angle plug with 24" cable and 3/16" fast-on connectors.
Used to replace speaker cable in many combo amplifiers where the speakers are
connected to the amplifier chassis via a 1/4" jack and plug.
Heavy-duty 16ga round black speaker cable,
right-angle plug and fast-on connectors for attachment to one
speaker.
Part #SCH-7080 |
$4.99 |
|


Click on photo for
larger view |
Revisit™
SPEAKER HARNESS
Replacement right-angle plug with 34" cable and 3/16" fast-on connectors.
Used to replace speaker cable in most combo amplifiers where the speakers are
connected to the amplifier chassis via a 1/4" jack and plug. 18ga black zip cord,
right-angle plug and fast-on connectors for attachment to one
speaker.
Part #SCH-280 |
$5.99 |
|


Click on photo for
larger view |
Revisit™
SPEAKER JUMPER CABLE
Teflon™ insulated silver plated copper speaker wire, 18 gauge, twisted pair,
black and white. Terminated at each end in standard 3/16" speaker
fast-on connectors. Great for connecting speakers in parallel in
2x12 or 4x12 cabinets. 24 inches (61 cm) long. Made in
USA.
Part #SJ-150 |
$5.99 |
|

Click on photo for
larger view |
JACK PLATE, BLACK METAL, SINGLE 1/4" JACK, 2" OUTSIDE DIAMETER. Similar in style to vintage Fender® jack plates. Works well with the Switchcraft J-11 1/4" jacks
that we carry. Hole is 3/8", for most Switchcraft type jacks. Easy to install, economical.
Jack not included - order separately. For size specifications, click here.
Part #JP-180 |
$1.39
|
|


Click on photo for
larger view |
Revisit™
JACK PLATE COMPLETE WITH
SWITCHCRAFT #11 JACK.
Switchcraft #11 jack preinstalled with lock washer and trim washer.
Outside diameter 2
inches (51mm). Designed to fit flush against a 1 1/8" (29mm) cabinet hole.
Easy to install - drill 1 1/8" hole in cabinet, attach speaker wiring to jack
and speaker, attach plate to cabinet.
Part #JPC-180 |
$4.95
|
|


Click on photo for
larger view |
Revisit™ JACK PLATE COMPLETE
WITH GENUINE SWITCHCRAFT #11 JACK and 24" SPEAKER WIRE.
Preassembled - includes 2" diameter single jack mounting plate with Switchcraft #11 jack preinstalled with lock washer and trim washer,
and 24 inch Teflon™-insulated 18 ga speaker wire terminated in 3/16" push-on
speaker connectors. Outside jack
plate diameter 2
inches (51mm). Designed to fit flush against a 1 1/8" (29mm) cabinet hole.
Easy to install - drill 1 1/8" hole in cabinet, attach speaker wiring to
speaker,
attach plate to cabinet. For two-speaker cabinets, see the JPH-182,
below.
Part #JPH-180 |
$11.95
|
|


Click on photo for
larger view |
Revisit™ JACK PLATE COMPLETE
WITH GENUINE SWITCHCRAFT #11 JACK and 24" SPEAKER WIRE, PLUS ADDITIONAL 24"
JUMPER.
Preassembled - includes 2" diameter single jack mounting plate with Switchcraft #11 jack preinstalled with lock washer and trim washer,
and 24 inch Teflon™-insulated 18 ga speaker wire terminated in 3/16" push-on
speaker connectors. Outside jack
plate diameter 2
inches (51mm). Designed to fit flush against a 1 1/8" (29mm) cabinet hole. Includes
a second 24 inch Teflon™-insulated 18 ga speaker wire terminated in 3/16"
push-on speaker connectors to connect to a second speaker in the same cabinet.
Easy to install - drill 1 1/8" hole in cabinet, attach speaker wiring to
speakers,
attach plate to cabinet.
Part #JPH-182 |
$15.95
|
|
|
Mesa/Boogie Knobs
(Also see our complete line of
knobs) |
|
|

Click on photo for
larger view |
KNOB, Chrome Dome all-metal knob for 1/4" shaft- secured by set-screw.
Knurled chrome dome amplifier knob measures 18.02 mm Dia. x 19.75 mm H
(0.72" x 0.78").
Has gold pointer. Looks
great as a replacement on newer Kustom, Genz-Benz, Mesa Boogie, etc.
Not recommended for Peavey, as most Peavey amps in the past 20 years use a 3/16"
diameter pot shaft. This knob is a set-screw type, designed for a 1/4"
shaft. Made of solid brass.
Part #K-200 |
$4.95 |
|

Click on photo for
larger view |
KNOB, Black Chrome Dome all-metal knob for 1/4" shaft - secured by
set-screw.
Knurled black chrome dome amplifier knob measures 19.4 mm Dia. x 19.3 mm H
(0.77" x 0.76").
Has gold pointer. Looks
great as a replacement on newer Kustom, Genz-Benz, Mesa Boogie, etc.
Not recommended for Peavey, as most Peavey amps in the past 20 years use a 3/16"
diameter pot shaft. This knob is a set-screw type, designed for a 1/4"
shaft. Made of solid brass.
Part #K-201 |
$5.95 |
|

Click on photo for
larger view |
KNOB, Mesa-Boogie®, Vintage Brown
Mesa-Boogie® style amp
knob, brown color with white pointer. Knob is secured by set-screw,
designed to fit a 1/4" shaft. Mesa-Boogie part number 408020. Used on the Mesa-Boogie Maverick Dual Rectifier model.
Part #K-316 |
$2.95
|
|

Click on photo for
larger view |
KNOB, Mesa-Boogie®, Vintage Brown,
Set of 6
Mesa-Boogie® style amp
knob, brown color with white pointer. Knob is secured by set-screw,
designed to fit a 1/4" shaft. Mesa-Boogie part number 408020.
Used on the Mesa-Boogie Maverick Dual Rectifier model.
Set of 6 knobs.
Part #K-316-6 |
$12.95
(for pack of 6 knobs) |
|
|
Mesa/Boogie Pot
Hardware
(Also see our complete line of pots) |
|
|

Click on photo for
larger view |
SAVE WITH MULTIPACK!
JNUT-38 JACK NUT AND WASHER, METAL,
SWITCHCRAFT®, SET OF 6
Genuine Switchcraft® nut and washer set for the blackface/silverface Fender® bias pot, Mesa Boogie pots, and the
CTS or Alpha pots with 3/8" bushing (found on original vintage Fender®
blackface and silverface), as well as Peavey® and Switchcraft®
1/4" jacks. Does NOT fit the 24mm Marshall® pots. Set of
6 washers and 6 nuts.
Part #JNUT-38-6 |
$3.99
(Set of 6 washers and 6 nuts) |
|
 |
JACK NUT AND WASHER, METAL,
SWITCHCRAFT®
Genuine Switchcraft® nut and washer set for the blackface/silverface Fender® bias pot, Mesa Boogie pots, and the
CTS or Alpha pots with 3/8" bushing (found on original vintage Fender®
blackface and silverface), as well as Peavey® and Switchcraft®
1/4" jacks. Does NOT fit the 24mm Marshall® pots.
Part #JNUT-38 |
$0.89
(Set of 1 washer and 1 nut) |
|

Click on photo for
larger view |
JACK LOCK WASHER, METAL
Replacement lock washer for all Alpha pots with 3/8" bushing and Mesa Boogie pots,
as well as Switchcraft 1/4" jacks.
Part #W-38 |
$0.49 |
|
|
Mesa/Boogie Power Cords |
|
|

Click on photo for
larger view |
Revisit™ 6 ft POWER CORD, DETACHABLE, 3-WIRE, 18ga, 6 ft LONG, IEC CONNECTOR AT EQUIPMENT END. COMMON REPLACEMENT CORD FOR MANY GUITAR AMPS, POWER AMPS, EFFECTS UNITS, ETC.
Standard NEMA 5-15 plug for North American use at 110-120 Volts AC.
IEC connector at equipment end. Used only in North America.
Part #PC-300 |
$5.95 |
|

Click on photo for
larger view |
Revisit™ 10 ft POWER CORD, DETACHABLE, 3-WIRE, 18ga, 10 ft LONG, IEC CONNECTOR AT EQUIPMENT END. REPLACEMENT CORD FOR MANY GUITAR AMPS, POWER AMPS, EFFECTS UNITS, ETC.
10 ft LENGTH GIVE EXTRA FLEXIBILITY IN EQUIPMENT PLACEMENT, REDUCES USE OF
EXTENSION CORDS.
Standard NEMA 5-15 plug for North American use at 110-120 Volts AC.
IEC connector at equipment end. Used only in North America.
Part #PC-600 |
$10.95 |
|

Click on photo for
larger view |
SUPER-LONG
Revisit™ 4 METER (about 13 ft) POWER CORD, 3-WIRE, 18ga, SVT type, "Thin
Line".
OUR LONGEST POWER CORD!
Cut ends for installing (soldered connection) into many vintage amps using a
3-wire cord (or for upgrading 2 wire cords in older amps).
Cord length is a super-long 13 feet, cord thickness is 0.24 inches (about 1/4" or
6.2mm).
Standard NEMA 5-15 plug for North American use at 110-120 Volts AC. Used only in
North America.
Part #PC-183SVT13-TL |
$14.95 |
|

Click on photo for
larger view |
EXTRA-LONG
Revisit™ 12 ft POWER CORD, 3-WIRE, 18ga, SJT type.
Cut ends for installing (soldered connection) into many vintage amps using a
3-wire cord (or for upgrading 2 wire cords in older amps).
Cord length is an extra-long 12 feet, cord thickness is 0.29 inches(about 9/32" or 7.3mm).
This cord is of appropriate gauge and physical thickness for application in most
medium to large guitar amps with "hard-wired" power cords (Fender, for example).
Standard NEMA 5-15 plug for North American use at 110-120 Volts AC. Used only in
North America.
Part #PC-183SJT12 |
$13.95 |
|
16 gauge:

Click on photo for
larger view |
LONG
10 ft POWER CORD, 3-WIRE, 16ga, SJT type. Cut end for installing
(soldered connection) into many vintage amps using a 3-wire cord (or for
upgrading 2 wire cords in older amps). Cord length is 10 feet,
cord thickness is 0.32 inches (about 5.6" or 8.1mm), wire gauge is 16ga.
Standard NEMA 5-15 plug for North American use at 110-120 Volts AC. Used only in
North America.
Part #PC-163SJT10 |
$12.95 |
|
18 gauge:

Click on photo for
larger view |
LONG
10 ft POWER CORD, 3-WIRE, 18ga, SJT type. Cut end for installing
(soldered connection) into many vintage amps using a 3-wire cord (or for
upgrading 2 wire cords in older amps). Cord length is 10 feet, cord thickness is 0.29 inches(about 9/32" or 7.3mm).
This cord is of appropriate gauge and physical thickness for application in most
medium to large guitar amps with "hard-wired" power cords (Fender, for example).
Standard NEMA 5-15 plug for North American use at 110-120 Volts AC. Used only in
North America.
Part #PC-183SJT10 |
$11.95 |
|

Click on photo for
larger view |
Revisit™ 8 ft POWER CORD, 3-WIRE, 18ga, SJT type.
Cut ends for installing (soldered connection) into many vintage amps using a
3-wire cord (or for upgrading 2 wire cords in older amps).
Cord length 8 feet, cord thickness is 0.29 inches(about 9/32" or 7.3mm).
This cord is of appropriate gauge and physical thickness for application in most
medium to large guitar amps with "hard-wired" power cords (Fender, for example).
Standard NEMA 5-15 plug for North American use at 110-120 Volts AC.
Used only in North America.
Part #PC-183SJT8 |
$9.95 |
|

Click on photo for
larger view |
8 ft POWER CORD, 3-WIRE, 18ga, SVT type,
"Thin Line". Cut ends for installing (soldered connection) into
many vintage amps using a 3-wire cord (or for upgrading 2 wire cords in older
amps). Cord length 8 feet, 18 gauge, cord thickness is 0.24 inches (about
1/4" or 6.1mm).
Thinner than the PC-183SJT8 cord, this cord is better suited for replacing amp
cords in smaller amplifiers where there was formerly a 2-wire cord without
ground.
Standard NEMA 5-15 plug for North American use at 110-120 Volts AC. Used only in
North America.
Part #PC-183SVT8-TL |
$9.95 |
|

Click on photo for
larger view |
Fender® style
reverb or AC cable clamp. Used on Fender amps since the early 60s to
hold the reverb cable to the side of the cabinet. Clamp is 3/8"
diameter, comes with 3/4" screw for mounting. Also used in some amplifiers
to hold the AC cord to the cabinet wall. Fender part number 022941.
Works on many other brands of amplifiers as well.
Part #RCC-381 |
$0.99 |
|

Click on photo for
larger view |
SMALL SIZED STRAIN RELIEF
Designed for
very small flat cords - two conductor (such as two conductor cords or dual audio
cable. Cable size is SJT-1 (0.120" x 0.220" .. or approximately 1/8"
thick x 1/4" wide). For a strain relief removal / installation
tool to make the job much easier, see the YTH-205 below.
Part #SR-1100 |
$0.89 |
|

Click on photo for
larger view |
LARGE SIZED STRAIN RELIEF FOR 35/64" X 5/8" HOLE
Popular strain relief found on most
vintage
guitar amplifiers with round power cords, including most vintage Fender® amps. Designed for 5/16" cord diameter.
Click here for specific dimensions of chassis hole.
For a strain relief removal / installation tool to make the job much easier,
see the YTH-205 below.
Part #SR-1200 |
$0.99 |
|

Click on photo for
larger view |
EXTRA-LARGE SIZED STRAIN RELIEF FOR 3/4" X
27/32" HOLE
Popular strain relief found on
a few
larger vintage power amplifiers with very thick power cords. Designed for 11/32" cord diameter.
Click here for specific dimensions of chassis hole.
For a strain relief removal / installation tool to make the job much easier,
see the YTH-205 below.
Part #SR-1300 |
$0.99 |
|

Click on photo for
larger view |
STRAIN RELIEF INSTALLATION/REMOVAL TOOL
Removing and installing strain reliefs can be a frustrating job.
Standard pliers just don't get the job done and can damage the strain relief.
These special strain relief pliers are just what you need. They fit
perfectly on AC power cord strain reliefs and give you the leverage you need to
compress the strain relief for easy removal and installation, without damage.
Part #YTH-205 |
$10.95 |
|

Click on photo for
larger view |
FUSE HOLDER, HIGH QUALITY USED WITH AGC
TYPE FUSE. ALSO A GOOD CHOICE FOR MESA BOOGIE.
Vintage 50's Fender® style fuse holder, replacement for many other brands,
especially Mesa Boogie. Twist-lock cap. Durable, rugged design - better than OEM.
Low profile so that cap does not extend beyond rear amp cabinet.
Fits "American" style AGC fuses (1/4" x 1 1/4").
Part #FH-301 |
$3.95 |
|
|
Mesa/Boogie®
Capacitors |
|
|

Click on photo for
larger view |
RADIAL ELECTROLYTIC
CAPACITOR, 10,000uF @ 16V.
This
size filter capacitor is commonly found in amplifiers which use DC voltage on
the filaments of some of the preamp tubes. Found in Marshall®,
Mesa-Boogie® as well as other brands. Working temperature range -40°C to
+105°C. 18mm diameter, 35mm tall (approximately 11/16" diameter X 1
3/8" tall)
Part #10000-16 |
$2.49
|
|
 |
CAPACITOR, SILVER MICA, RADIAL
10pF @ 500V
±5% Radial lead, dipped in epoxy coating. 10 pico-Farad @ 500V 1000pF
= 1nF = 0.001uF
Part #C-SM-010-5 |
$0.60 |
|
 |
CAPACITOR, SILVER MICA, RADIAL
12pF @ 500V
±5% Radial lead, dipped in epoxy coating. 12 pico-Farad @ 500V
1000pF = 1nF = 0.001uF
Part #C-SM-012-5 |
$0.60 |
|
 |
CAPACITOR, SILVER MICA, RADIAL
22pF @ 500V
±5% Radial lead, dipped in epoxy coating. 22 pico-Farad @ 500V
1000pF = 1nF = 0.001uF
Part #C-SM-022-5 |
$0.60 |
|
 |
CAPACITOR, SILVER MICA, RADIAL
47pF @ 500V
±5% Radial lead, dipped in epoxy coating. 47 pico-Farad @ 500V 1000pF
= 1nF = 0.001uF
Part #C-SM-047-5 |
$0.60 |
|
 |
CAPACITOR, SILVER MICA, RADIAL
68pF @ 500V
±5% Radial lead, dipped in epoxy coating. 68 pico-Farad @ 500V 1000pF
= 1nF = 0.001uF
Part #C-SM-068-5 |
$0.60 |
|
 |
CAPACITOR, SILVER MICA, RADIAL
82pF @ 500V
±5% Radial lead, dipped in epoxy coating. 82 pico-Farad @ 500V 1000pF
= 1nF = 0.001uF
Part #C-SM-082-5 |
$0.60 |
|
 |
CAPACITOR, SILVER MICA, RADIAL
100pF @ 500V
±5% Radial lead, dipped in epoxy coating. 100 pico-Farad @ 500V
1000pF = 1nF = 0.001uF
Part #C-SM-100-5 |
$0.65 |
|
 |
CAPACITOR, SILVER MICA, RADIAL
120pF @ 500V
±5% Radial lead, dipped in epoxy coating. 120 pico-Farad @ 500V
1000pF = 1nF = 0.001uF
Part #C-SM-120-5 |
$0.65 |
|
 |
CAPACITOR, SILVER MICA, RADIAL
150pF @ 500V
±5% Radial lead, dipped in epoxy coating. 150 pico-Farad @ 500V 1000pF
= 1nF = 0.001uF
Part #C-SM-150-5 |
$0.65 |
|
 |
CAPACITOR, SILVER MICA, RADIAL
220pF @ 500V
±5% Radial lead, dipped in epoxy coating. 220 pico-Farad @ 500V
1000pF = 1nF = 0.001uF
Part #C-SM-220-5 |
$0.80 |
|
 |
CAPACITOR, SILVER MICA, RADIAL
300pF @ 500V
±5% Radial lead, dipped in epoxy coating. 300 pico-Farad @ 500V
1000pF = 1nF = 0.001uF
Part #C-SM-300-5 |
$0.90 |
|
 |
CAPACITOR, SILVER MICA, RADIAL
500pF @ 500V
±5% Radial lead, dipped in epoxy coating. 500 pico-Farad @ 500V 1000pF
= 1nF = 0.001uF
Part #C-SM-500-5 |
$1.00 |
|
 |
CAPACITOR, SILVER MICA, RADIAL
750pF @ 500V
±5% Radial lead, dipped in epoxy coating. 750 pico-Farad @ 500V 1000pF
= 1nF = 0.001uF
Part #C-SM-750-5 |
$1.69 |
|
 |
CAPACITOR, POLYPROPYLENE, RADIAL - SIMILAR
TO ORANGE DROP STYLE,
.001uF @ 630V
Part #C-PR-102-6 |
$0.30 |
|
 |
CAPACITOR, POLYPROPYLENE, RADIAL - SIMILAR
TO ORANGE DROP STYLE,
.0022uF @ 630V
Part #C-PR-222-6 |
$0.30 |
|
 |
CAPACITOR, POLYPROPYLENE, RADIAL - SIMILAR
TO ORANGE DROP STYLE,
.0047uF @ 630V
Part #C-PR-472-6 |
$0.30 |
|
 |
CAPACITOR, POLYPROPYLENE, RADIAL - SIMILAR
TO ORANGE DROP STYLE,
.01uF @ 630V
Part #C-PR-103-6 |
$0.35 |
|
 |
CAPACITOR, POLYPROPYLENE, RADIAL - SIMILAR
TO ORANGE DROP STYLE,
.022uF @ 630V
Part #C-PR-223-6 |
$0.35 |
|
 |
CAPACITOR, POLYPROPYLENE, RADIAL - SIMILAR
TO ORANGE DROP STYLE,
.047uF @ 630V
Part #C-PR-473-6 |
$0.40 |
|
 |
CAPACITOR, POLYPROPYLENE, RADIAL - SIMILAR
TO ORANGE DROP STYLE,
.1uF @ 630V
Part #C-PR-104-6 |
$0.50 |
|
 |
CAPACITOR, POLYPROPYLENE, RADIAL - SIMILAR
TO ORANGE DROP STYLE,
.22uF @ 630V
Part #C-PR-224-6 |
$0.70 |
|
 |
CAPACITOR, POLYPROPYLENE, RADIAL - SIMILAR
TO ORANGE DROP STYLE,
.47uF @ 630V
Part #C-PR-474-6 |
$1.50 |
|
|
Mesa/Boogie Reverb Tanks |
|
|


Click on photo for
larger view
 |
Revisit™ Reverb Tank, 17" long, 2 spring, equivalent to Accutronics 4AB3C1B. Input impedance
8 ohms, output impedance 2250 ohms, long decay (2.75 - 4.0 seconds), input insulated/output grounded, designed for horizontal mounting, open side down.
Used in Mesa Boogie® MK2C, Mesa Express and others. See explanation of Accutronics reverb tank numbering system here. See a chart which lists AC impedance
and DC resistance measurements for reverb tanks
here.
Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet.
View the 2-year warranty details
here.
Part #4AB3C1B "Bringing back the sound of vintage Accutronics tanks" |
$30.99 |
|


Click on photo for
larger view
|
Accutronics Reverb Tank, 17" long, 2 spring, 4AB3C1B. Input impedance
8 ohms, output impedance 2250 ohms, long decay (2.75 - 4.0 seconds), input insulated/output grounded, designed for horizontal mounting, open side down.
Primarily used by all Fender®
amplifiers with tube reverb from 1963-1990. Also used in Reissue
models like: Fender® Princeton Reverb, Fender® Deluxe Reverb,
Fender® Vibrolux Reverb, Fender® Pro Reverb, Fender® Super Reverb , Fender® Twin
Reverb, Fender® Quad Reverb , Fender® Super Six Reverb,
Fender® Vibrosonic , Fender® 63 Reverb Unit Reissue, Fender®`65 Princeton Reverb
Reissue,
Fender® 65 Deluxe Reverb Reissue, Fender® 65 Super Reverb Reissue, Fender® 65
Twin Reverb Reissue, Fender® 65 Twin Custom(TM) 15, Fender® Concert II.
Also used in Mesa Boogie® MK2C and others, LAB Series L5, L7, L9,
Koch® Powertone I, Ampeg VT-40, Ampeg Super Rocket SR212 and B-52 AT-100. See explanation of Accutronics reverb tank numbering system here. See a
chart which lists AC impedance and DC resistance measurements for reverb tanks
here.
Part #ACC-4AB3C1B |
$32.99 |
|


Click on photo for
larger view
 |
Revisit™ Reverb Tank, 17" long, 2 spring, equivalent to Accutronics 4BB3A1B. Input impedance 150 ohms, output impedance 2250 ohms,
medium decay (1.5 - 2.75 seconds), input grounded/output grounded, designed for
horizontal mounting, open side down. Common replacement for Music
Man, and the Mesa Boogie F-50. See explanation of Accutronics reverb tank numbering system here.
See a chart which lists AC impedance and DC resistance measurements for reverb
tanks here.
Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet.
View the 2-year warranty details
here.
Part #4BB2A1B"Bringing back the sound of vintage Accutronics tanks" |
$30.99 |
|


Click on photo for larger view
 |
Revisit™ Reverb Tank, 9" long, 3 spring, equivalent to Accutronics 8AB2A1B. Short Tank, Medium Decay, input impedance 10 ohms, output 2575 ohms, grounded input and grounded output. Mounts horizontal, open side down.
Found in some Mesa Boogie and
Fender® Models. See explanation of Accutronics reverb tank numbering system here.
See a chart which lists AC impedance and DC resistance measurements for reverb
tanks here.
Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet.View the 2-year warranty
details here.
Part #8AB2A1B "Bringing back the sound of vintage Accutronics tanks" |
$30.99
|
|


Click on photo for larger view
 |
Revisit™ Reverb Tank, 9" long, 3 spring,
equivalent to Accutronics
8AB2A1C. Short Tank, Medium Decay, input
impedance 10 ohms, output 2575 ohms, grounded input and grounded output. Mounts
on vertical wall, long axis horizontal, connectors up. Used
as an upgrade external tank in the Mesa Boogie Caliber 50+. See explanation of Accutronics reverb tank numbering system
here. See a chart which lists AC impedance and DC resistance
measurements for reverb tanks here.
Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet.View the 2-year warranty
details here.
Part #8AB2A1C
"Bringing back the sound of vintage Accutronics tanks" |
$30.99
|
|


Click on photo for larger view
 |
Revisit™ Reverb Tank, 9" long, 3 spring, equivalent to Accutronics 8BB2C1B.
Short Tank, Medium Decay, input impedance 190 ohms, output 2575 ohms, insulated
input and grounded output. Mounts horizontal, open side down.
Primarily used by Rivera PUBSTER 25 & CHUBSTER 40 , Rivera Knucklehead Reverb,
Vox® AC30, with solid state reverb as used in the Seventies, Crate Palomino V32 &
V16, Music Man RD50, Kitty Hawk Supreme, Marshall® G80RCD, Marshall® G100RCD. Upgrade for Laney
VC15 (part nr. 10006), Brunetti Singleman, Mesa Boogie Rectoverb.
See explanation of Accutronics reverb tank numbering system here.
See a chart which lists AC impedance and DC resistance measurements for reverb
tanks here.
Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet.
View the 2-year warranty details
here.
Part #8BB2C1B "Bringing back the sound of vintage Accutronics tanks" |
$30.99
|
|


Click on photo for larger view
 |
Revisit™ Reverb Tank, 9" long, 3 spring, equivalent to Accutronics 8FB3C1B. Short
Tank, Long Decay, input impedance 1925 ohms, output 2575 ohms, insulated input
and grounded output. Mounts horizontal, open side down.
See explanation of Accutronics reverb tank numbering system here.
See a chart which lists AC impedance and DC resistance measurements for reverb
tanks here.
Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet.
View the 2-year warranty
details here.
Part #8FB3C1B
"Bringing back the sound of vintage Accutronics tanks" |
$30.99
|
|


Click on photo for
larger view
 |
Revisit™ Reverb Tank, 17" long, 3 spring, equivalent to Accutronics 9AB2A1B. Input impedance 10 ohms, output impedance 2575 ohms, medium decay (1.5 - 2.75 seconds), input
and output grounded, designed for horizontal mounting, open side down. Common replacement for
Mesa Boogie® MK I, MK II, MK III, MK IV, MK V, Lonestar, Lonestar Special,
Electradyne, Royal Atlantic 100, Roadster, RoadKing II, TremoVerb, Express
Series, DC Series, Hearbreaker, Blue Angel, TransAtlantic TA-30, and Maverick.
Also used in some Fender®, Vox® AC30 (1960s+70s),
and
Engl Screamer (E330, E335) See explanation of Accutronics reverb tank numbering system here. See a
chart which lists AC impedance and DC resistance measurements for reverb tanks
here.
Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet.View the 2-year warranty
details here.
Part #9AB2A1B
"Bringing back the sound of vintage Accutronics tanks" |
$34.99
|
|


Click on photo for
larger view
 |
Revisit™ Reverb Tank, 17" long, 3 spring, equivalent to Accutronics 9AB3A1B. Input impedance 10 ohms, output impedance 2575 ohms,
long decay (2.75 - 4 seconds), input
and output grounded, designed for horizontal mounting, open side down.
A longer decay replacement for
Mesa Boogie® MK I, MK II, MK III, MK IV, MK V, Lonestar, Lonestar Special,
Electradyne, Royal Atlantic 100, Roadster, RoadKing II, TremoVerb, Express
Series, DC Series, Hearbreaker, Blue Angel, TransAtlantic TA-30, and Maverick.
Also may be used in some Fender®, Vox® AC30 (1960s+70s),
and
Engl®
Screamer (E330, E335) See explanation of Accutronics reverb tank numbering system here. See a
chart which lists AC impedance and DC resistance measurements for reverb tanks
here.
Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet.View the 2-year warranty
details here.
Part #9AB3A1B
"Bringing back the sound of vintage Accutronics tanks" |
$34.99
|
|


Click on photo for
larger view |
Rubber mounting grommets for
reverb tanks, package of four. Provides shock absorption for
tanks mounted directly to the inside of a wooden amp cabinet. Mounting
Hole Diameter = 3/8" Outer Diameter = 1/2"
Part #RRG-4 |
$1.99
(For a pack of 4 grommets - In Stock) |
|


Click on photo for
larger view |
TRANSFORMER,
Revisit™
Mesa-Boogie® REVERB DRIVER.
For vintage Mesa-Boogie® models, including vintage Mark I through Mark IV,
Subway Blues, Studio 22, Studio Caliber, Maverick, Lonestar Special, and many
others . Mesa Boogie® part number 550185. 10" cut leads, X-Mount with 1 3/4" mounting
centers. Input impedance 14.5K ohms, output impedance 4 ohms.
Part #RT-921 |
$14.95 |
|


Click on photo for
larger view |
3 foot Revisit™ right angle RCA cables for Reverb Tanks and other electronic devices.
Dual cable, excellent shielding properties, 3 feet long.
Part #RC-173 |
$3.95
In Stock |
|


Click on photo for
larger view |
3 foot Extra Heavy-Duty Revisit™ right angle RCA cables for Reverb Tanks and other electronic devices.
Heavy duty thick cable, gold RCA connectors, excellent shielding properties, additional ground conductor
provided.
Part #RC-273 |
$6.95
In stock |
|


Click on photo for
larger view |
4 foot Revisit™ right angle RCA cables for Reverb Tanks and other electronic devices.
Dual cable, excellent shielding properties, 4 feet long.
Part #RC-174 |
$4.95
In stock |
|


Click on photo for
larger view |
4 foot Revisit™ right angle cables for Reverb Tanks.
RCA at one end, stripped cable at opposite end. For connecting
reverb tanks directly to a PC board via a soldered connection at the PC board
end. Used by a number of manufacturers.
Dual cable, excellent shielding properties, 4 feet long.
Part #RC-374 |
$4.95
In stock |
|


Click on photo for
larger view |
5 foot Revisit™ right angle RCA cables for Reverb Tanks and other electronic devices.
Dual cable, excellent shielding properties, 5 feet long.
Part #RC-175 |
$5.95
In stock |
|


Click on photo for
larger view |
6 foot Extra Heavy-Duty Revisit™ right angle RCA cables for Reverb Tanks and other electronic devices.
Heavy duty thick cable, gold RCA connectors, excellent shielding properties, additional ground conductor
provided.
Part #RC-276 |
$9.95
In stock |
|
|
Mesa/Boogie Switches
(Also see our complete line of switches) |
|
|

Click on photo for
larger view |
SWITCH, STANDARD SIZE TOGGLE -
Rated at 20 Amps (125VAC) or 15 Amps (250VAC). Fits 1/2" chassis
hole. Solder terminals or 1/4" push on, single pole / single throw (SPST).
Two position - on/off. NOTE: RATED FOR AC SERVICE ONLY AT
250V MAX - DO NOT USE AS A GUITAR AMPLIFIER STANDBY SWITCH.
Part #STS-20 |
$3.95 |
|

Click on photo for
larger view |
SWITCH, CARLING SPST TOGGLE,
Good replacement for Mesa Boogie power or standby switches in larger heads (such
as the Dual or Triple Recitifier). Original Fender® part.
Made by Carling.
Part #SW-495 |
$4.95 |
|

Click on photo for
larger view |
SAVE WITH MULTIPACK! 2 SWITCHES, CARLING SPST TOGGLE, ORIGINAL REPLACEMENT FOR
Mesa Boogie Amps.
Change both the power and standby switches on your amp at the same time, and
save! Made by Carling
Part #SW-495X2 |
$8.95 |
|

Click on photo for
larger view |
SWITCH, STANDARD SIZE TOGGLE - MADE BY CARLING
- RATED AT 15A, 125VAC.
TWO POSITION (ON/OFF), DOUBLE POLE (DPST).
FITS 1/2" CHASSIS HOLE.
SOLDER TERMINALS OR 1/4" PUSH-ON.
Fender® PART NUMBER
0036570000. Made by Carling.
Part #SW-525 |
$6.95 |
|

Click on photo for
larger view |
SWITCH, STANDARD SIZE TOGGLE - Made by
Carling - rated at 15A, 125VAC. Two position (on/off), single pole (SPST). Fits
1/2" chassis hole. Solder terminals.
Part #SW-526 |
$4.95 |
|

Click on photo for
larger view |
SWITCH, STANDARD SIZE TOGGLE - RATED AT
10 Amps (125VAC) or 6 Amps (250VAC) - TWO POSITION (ON/ON).
Fits 1/2" chassis hole. Screw terminals, or remove screws for
soldered connections. Double-pole double-throw, no center
off - two positions (ON/ON).
Part #STS-15-DPDT |
$5.95 |
|

Click on photo for
larger view |
SWITCH, STANDARD SIZE TOGGLE - RATED AT
15 Amps (125VAC) or 10 Amps (250VAC) - THREE POSITION (ON/OFF/ON).
Fits 1/2" chassis hole. Screw terminals, or remove screws for
soldered connections. Double-pole double-throw, with center
off - three positions (ON/OFF/ON).
Part #STS-15-DPDT-CO |
$6.50 |
|

Click on photo for
larger view |
FOOT SWITCH,
CARLING BRAND, SPDT,
LATCHING
Found in many type of footswitches. Has 3 electrical terminals (single pole, double throw).
Solder lugs for wire. Made by Carling.
Part #FS-492 |
$9.95 |
|

Click on photo for
larger view |
FOOT SWITCH,
CARLING BRAND, SPST,
LATCHING, REPLACEMENT FOR Fender®, ETC.
Carling SPST footswitch. Used in Marshall® etc. Reverb/tremolo/channel switching pedals.
Has 2 electrical terminals (single pole, single throw).
Solder lugs for wire.
Made by Carling.
Part #FS-493 |
$9.95 |
|

Click on photo for
larger view |
FOOT SWITCH,
DPDT, LATCHING, PC MOUNT, FOR SWITCHING AND EFFECTS.
Double-pole Double-Throw, made for direct connection to a PC board. Has 6 electrical terminals.
Part #FS-498-PC
(Also see our complete line of switches) |
$3.95 |
|
|
Fans |
|
|

Click on photo for
larger view |
ThermoCool Fan.
120 x 38mm Ball Bearing 72 CFM.
This size is commonly found in Mesa-Boogie Mark series amps.
Thermocool axial fans provide enhanced cooling for a variety of electronic
devices. Leading air flow technology is designed into every Thermocool product
resulting in reduced turbulence, low noise levels and a more energy efficient
product. Thermocool fans are ideal for use in computer systems, portable CD and
DVD players, stereo components, overhead projectors, laptop computers, and many
other electronic applications where circulation is a key concern.
For plug in wiring harness, order 25-0050 fan cord separately. For use on
100-125VAC System only, as found in North America, Japan, etc. This
size commonly found in Mesa-Boogie Mark series amps.
Specifications: • Power:
100-125V
AC, 50-60 Hz • Ball bearing • Terminal connection • 0.22 amps • 2200 RPM • 39dB
noise level • 72CFM air flow • Dimensions: 120 mm (H) x 120 mm (W) x 38 mm
(D).
Ratings: Reliability: A, Airflow: A,
Noise: A-, Price: B-
[4 3/4" (H) x 4 3/4" (W) x 1 1/2" (D)]
Part #G12038MAS |
$21.95 |
|

Click on photo for
larger view |
Standard 12" fan cord with 90° angled plug.
For use with 110~120 VAC cooling fans with .110" terminals; non-terminated
on opposite end. Great for use with G12038MAS
fans, above.
Part #25-0050 |
$2.95 |
|