Peavey Hardware



Click on photo for
larger view
TUBE RETAINER WITH GRIP TEETH, DESIGNED FOR OCTAL TUBES WITH PHENOLIC BASE SUCH AS 6L6 OR EL34.   USED IN PEAVEY AND MANY OTHER AMPS.  1 1/2" MOUNTING CENTERS.  SUPER HIGH QUALITY.
Part #TC-142
$1.95


Click on photo for
larger view
TUBE SHIELD, BAYONET "PUSH AND TWIST" TYPE, ALUMINUM, 1 15/16" TALL.  Includes new base, if needed.  Spring in top of shield fits over the tube.  Fits 12AX7A and similarly sized preamp tubes. Replacement for Fender® and many other brands.  Holes in base spaced 1 1/8" apart.
 
Part #TS-325S
$1.95  


Click on photo for
larger view
TUBE SHIELD, BAYONET "PUSH AND TWIST" TYPE, ALUMINUM, 1 15/16" TALL, SET OF 6.  Includes new bases, if needed.  Spring in top of shield fits over the tube.  Fits 12AX7A and similarly sized preamp tubes. Replacement for Fender® and many other brands.  Holes in base spaced 1 1/8" apart. 
 
Part #TS-325S-6
$8.95  


Click on photo for
larger view
REPLACEMENT CAP FOR FUSE HOLDER - Peavey®
Cap for fuse holder found in many Peavey® products.   Common failure item in Peavey®.   Original Peavey® part number
70900281
Part #FH-203
$3.99  


Click on photo for
larger view
FUSE HOLDER -  Peavey®, Fender®,  many other brands - AGC TYPE FUSE
Fuse holder found in many styles of guitar amplifiers, power amps and effects units.  For example, this fuse holder is used in the Peavey Valve King series.  Also used by Fender® - Fender® part number 0022546000.    PC Board mounted.   Uses AGC type 1/4" x 1 1/4" fuse
Part #FH-2709
$7.99

Speaker Protection Fuse
Used in many pro audio crossover circuits to help protect the driver - this size is commonly found in Peavey.   As the audio power increases, this device heats up (and even lights up at high power levels).  As it heats its resistance increases, thereby reducing the audio power reaching the driver.   This version only may be snapped into holders on the crossover PC board.   It is not designed to work with hard-soldered fuse types.   Size 8.3mm (5/16") diameter of the end caps x 38mm (1.5") long
Part # E-211
$1.99



Click on photo for
larger view
GENUINE PEAVEY CHROME/BLACK GUITAR AMP HANDLEBlack handle strap, metal reinforced.  Chrome metal caps.   Screws and T-Nuts are included.   Handle strap is 7/8" wide.   Designed for screw holes set 7 inches apart.   Total length of handle when properly mounted is 9 inches. 
Part #PAH-302
$7.99  



Click on photo for
larger view
Revisit™ BLACK GUITAR AMP HANDLE, WITH HARDWARE Rugged rubber black handle strap, steel reinforced.  Black metal caps.   Black 10-32 screws and  T-Nut mounting hardware are included.  Handle strap is 7/8" wide.   Designed for screw holes set 8 1/4 to 8 3/8 inches apart.   Total length of handle when properly mounted is 10 1/4".  
Part #GAH-271B
$7.99  



Click on photo for
larger view
Revisit™ GUITAR AMP HANDLE - BLACK.  Rugged rubber black handle strap, steel reinforced.  Black metal caps.   Screws not included - recommend using our SC-403B Black 10-32 type screws along with a 10-32 T-Nut for secure mounting.   Handle strap is 7/8" wide.   Designed for screw holes set 8 1/4 inches apart.   Total length of handle when properly mounted is 10 1/4".
Part #GAH-1
$6.99  



Click on photo for
larger view
Revisit™ ECONOMY GUITAR AMP HANDLE - BLACK.  Black plastic handle strap, metal reinforced.  Black metal caps.   Screws not included - recommend using our SC-403B Black 10-32 type screws along with a 10-32 T-Nut for secure mounting.   Handle strap is 7/8" wide.   Designed for screw holes set 8 inches apart.   Total length of handle when properly mounted is 9 1/2".   Not recommended for amps weighing over 30 pounds (14 kg).
Part #EAH-1
$3.99  


Click on photo for
larger view

BLACK HANDLE SCREWS
Pack of 2 stainless-steel handle screws finished in satin black for use with black end-cap handles, such as our GAH-1 or GAH-271B.  1" Long, 10-32 threads, finished in satin black to match black end caps.   Designed to work with a 10-32 T-Nut, in cabinet wood of 3/4" or less.    Will not work with external nut - must be a T-Nut.   Will not work with cabinet wood thicker than 3/4".   See Data Sheet here
Part #SC-403B
$0.99
(for a pack of 2 screws)
 


Click on photo for
larger view

HANDLE SCREWS
Pack of 2 stainless steel handle screws for GAH-271C Handle.   1" Long, 10-32 threads.   Designed to work with a 10-32 T-Nut, in cabinet wood of 3/4" or less.    Will not work with external nut - must be a T-Nut.   Will not work with cabinet wood thicker than 3/4".  See Data Sheet here
Part #SC-403
$0.99
(for a pack of 2 screws)
 


Click on photo for
larger view
PEAVEY CORD WRAP BRACKET.   THERE MUST BE A GAZILLION DIFFERENT PEAVEY AMPS WITH THESE CORD WRAP BRACKETS ON THE BACK.   VERY HANDY, AS MANY PEAVEY AMPS HAD SOME RATHER LONG HARD-WIRED NON-REMOVABLE CORDS.  BUT WHEN THEY BREAK AFTER MANY YEARS' USE, THEY'RE KIND OF USELESS.  REPLACE THEM NOW WITH THE ORIGINAL BRACKET.   ORIGINAL PEAVEY PART NUMBER 70900029.
(Bracket measures 2.45" horizontally. Mount measures .935" horizontally, and .941" vertically. Length of cylindrical shaft is .175" and the diameter is .19".)
Part #CW-119
$3.59
(each)


Click on photo for
larger view
CUP WASHER, BLACK METAL, PACK OF 10.  USED WITH #8 BLACK SCREW ON AMP AND SPEAKER CABINETS.
Part #BCW-10
$1.29
(pack of 10)
 



Click on photo for
larger view
SPEAKER BAFFLE MOUNTING SCREW WITH BOTH WOOD AND MACHINE THREADS, SET OF 4.   Locking nut and washer included.  Phillips head.   Drill hole, insert and tighten screws into wood from front of baffle.  Install grill cloth, and you have professional speaker mounting studs.   Replacement for original Fender® speaker mounting studs.    Set of 4.
Part #SC-409-4
$2.29
(For a pack of 4 screws with nuts and lock washers)
 


Click on photo for
larger view
BLACK PAN-HEAD WOOD SCREWS, #8 X 1/2", PACK OF 10.   USED IN AMPLIFIERS, SPEAKER CABINETS, AUTOMOTIVE.
Part #BWS8-5
$0.89
(pack of 10)
 


Click on photo for
larger view
BLACK PAN-HEAD WOOD SCREWS, #8 X 3/4", PACK OF 10.   USED IN AMPLIFIERS, SPEAKER CABINETS, AUTOMOTIVE.
Part #BWS8-75
$0.95
(pack of 10)
 


Click on photo for
larger view
BLACK PAN-HEAD WOOD SCREWS, #8 X 1", PACK OF 10.   USED IN AMPLIFIERS, SPEAKER CABINETS, AUTOMOTIVE.
Part #BWS8-1
$1.05
(pack of 10)
 


Click on photo for
larger view
BLACK PAN-HEAD WOOD SCREWS, #8 X 1 1/2", PACK OF 10.   USED IN AMPLIFIERS, SPEAKER CABINETS, AUTOMOTIVE.
Part #BWS8-15
$1.19
(pack of 10)




Click on photo for
larger view
CAGE NUT, ZINC, 10-32 THREAD.   Used on square-punched amp chassis rails to secure the chassis to the cabinet.   Frequently found in Peavey, Crate, Ampeg, other brands.   NOT used in Marshall® - see the MCN-4.   Works with all 10-32 screws.   Verify screw thread before ordering, as not all cage nuts are 10-32.   Zinc coating retards oxidation.   Pack of 4 nuts.   Made in Canada by Hammond Industries.
Part CNA-1421
$4.29
(pack of 4)
 


Click on photo for
larger view
CHROME GLIDE FEET, ORIGINAL PEAVEY, PACK OF 4, SCREWS INCLUDED.  Chrome cover over rubber foot.  1.55" Diameter, 0.44" Tall.   Used on many Peavey amplifiers.   Peavey part number 00051300.
Part #CG-251
$6.95
(pack of 4)


Click on photo for
larger view
SMALL BLACK RUBBER FEET, PACK OF 4.   3/4" DIAMETER AT TOP, 5/8" DIAMETER AT BOTTOM, 5/16" TALL.  BLACK RUBBER WITH METAL INSERT.   USED TO SUPPORT EFFECTS, SMALLER AMPS, SMALLER MIXERS.  SCREWS NOT INCLUDED.
Part #BRF-4
$2.95
(pack of 4)
 


Click on photo for
larger view
SMALL BLACK RUBBER FEET, SET OF 4.  
This heavy-duty rubber foot offers a sure grip on all types of surfaces. Ideal for smaller amps, amp heads, or speaker cabinets. The integral metal washer in the mounting hole helps prevent mounting screw "break-through" and adds overall durability.  Just under 1 inch - 15/16" diameter at the top, rounded down to 5/8" diameter at the bottom, and 3/8" tall.    Screws not included.    Set of 4 feet.
Part #BRF-723
$3.95
(pack of 4)
 


Click on photo for
larger view
MEDIUM BLACK RUBBER FEET, SET OF 4.  
This heavy-duty rubber foot offers a sure grip on all types of surfaces. Ideal for amp heads, combo amps, or smaller speaker cabinets. The integral metal washer in the mounting hole helps prevent mounting screw "break-through" and adds overall durability. 1" diameter x 5/8" tall. Mounting screws not included.
Part #BRF-1692
$4.95
(pack of 4)
 


Click on photo for
larger view
MEDIUM BLACK RUBBER FEET, SET OF 4.  
This heavy-duty rubber foot offers a sure grip on all types of surfaces. Ideal for large rack cabinets or speaker cabinets. The integral metal washer in the mounting hole helps prevent mounting screw "break-through" and adds overall durability. 1" diameter x 1" tall. Mounting screws not included.

Part #BRF-1691
$4.95
(pack of 4)
 


Click on photo for
larger view
MEDIUM BLACK RUBBER FEET, SET OF 4.   TAPERED -1 3/16" DIAMETER AT SMALL END, 1 1/4" DIAMETER AT LARGE END.   1/2" TALL.  BLACK RUBBER WITH METAL INSERT.   USED TO SUPPORT EFFECTS, AMPS,  MIXERS.   MOUNTING SCREWS NOT INCLUDED.
Part #BRF-9112
$4.95
(pack of 4)
 


Click on photo for
larger view
X-LARGE BLACK RUBBER FEET, SET OF 4.   TAPERED -  1 5/8" DIAMETER AT LARGE END, 1 1/4" AT SMALL END.  3/4" TALL.  BLACK RUBBER WITH METAL INSERT.   USED TO SUPPORT AMP HEADS, SPEAKER CABINETS.  MOUNTING SCREWS NOT INCLUDED.
Part #BRF-9107
$7.95
(pack of 4)
 


Click on photo for
larger view
Fender® Style Flat Mount 2" Caster Wheels - Set of 4.    Great for Fender® and many other brands of amps or cabinets.   Each wheel capable of supporting 45 lbs, or 180 lbs total for the set of 4.   Wheels 2" in diameter.   Specifications found here.   Note:  Mounting screws NOT included.
Part #FCW-4F
$24.95
(Set of 4 casters)

NOT SOLD OUTSIDE THE USA
 


Click on photo for
larger view
Fender® Style Pop-Out 2" Caster Wheels - Set of 4.    Great for Fender® and many other brands of amps or cabinets.   Each wheel capable of supporting 45 lbs, or 180 lbs total for the set of 4.   Wheels 2" in diameter.  The same type of removable caster wheels used on Fender® amps since the 1960s.   Note:  Mounting screws NOT included.   Must drill 5/8" hole in bottom of cabinet to accomodate post for wheel.
Part #FCW-4R
$28.95
(Set of 4 pop-out casters)

NOT SOLD OUTSIDE THE USA


Click on photo for
larger view
SMALL SIZED STRAIN RELIEF
Designed for very small flat cords - two conductor (such as two conductor cords or dual audio cable.  Cable size is SJT-1 (0.120" x 0.220" .. or approximately 1/8" thick x 1/4" wide).   For a strain relief removal / installation tool to make the job much easier, see the YTH-205 below.
Part #
SR-1100
$0.89  


Click on photo for
larger view
LARGE SIZED STRAIN RELIEF FOR 35/64" X 5/8" HOLE
Popular strain relief found on most vintage guitar amplifiers with round power cords, including most vintage Fender® amps.   Designed for 5/16" cord diameter.   Click here for specific dimensions of chassis hole.  For a strain relief removal / installation tool to make the job much easier, see the YTH-205 below.
Part #SR-1200
$0.99


Click on photo for
larger view
EXTRA-LARGE SIZED STRAIN RELIEF FOR 3/4" X 27/32" HOLE
Popular strain relief found on a few larger vintage power amplifiers with very thick power cords.  Designed for 11/32" cord diameter.   Click here for specific dimensions of chassis hole.   For a strain relief removal / installation tool to make the job much easier, see the YTH-205 below.
Part #SR-1300
$0.99


Click on photo for
larger view
STRAIN RELIEF INSTALLATION/REMOVAL TOOL
Removing and installing strain reliefs can be a frustrating job.   Standard pliers just don't get the job done and can damage the strain relief.   These special strain relief pliers are just what you need.  They fit perfectly on AC power cord strain reliefs and give you the leverage you need to compress the strain relief for easy removal and installation, without damage.
Part #YTH-205
$10.95


Click on photo for
 larger view
Revisit™ SPEAKER HARNESS - ECONOMY
Replacement right-angle plug with 34" cable and 3/16" fast-on connectors.    Used to replace speaker cable in most combo amplifiers where the speakers are connected to the amplifier chassis via a 1/4" jack and plug.   18ga black zip cord, right-angle plug and fast-on connectors for attachment to one speaker.  
Part #SCH-280
$5.99  


Click on photo for
 larger view
Revisit™ SPEAKER JUMPER CABLE
Teflon™ insulated silver plated copper speaker wire, 18 gauge, twisted pair, black and white.   Terminated at each end in standard .187 speaker push-on connectors.   Great for connecting speakers in parallel in 2x12 or 4x12 cabinets.   24 inches (61 cm) long.   Made in USA.
Part #SJ-150
$5.99  


Strat®, Stratocaster®, Esquire®, Telecaster®, Tele®, Jazzmaster®, Jaguar®, Mustang®, P.Bass®, J.Bass® and Fender® are registered trademarks of Fender® Musical Instruments. The replacement necks and bodies are for a Fender® or Squier® by Fender® guitar or bass. The distinctive headstock designs and the distinctive body designs of the Stratocaster®, Telecaster®, J.Bass®, P.Bass® and Tele® Bass are registered trademarks of Fender® Musical Instruments Co.  
Peavey® is a registered trademark of Peavey® Electronics Corporation.
Marshall® is a registered trademark of Marshall® Amplification Plc.
Mesa Boogie® is a registered trademark of MESA/Boogie® Ltd.
AmpRepairParts.com and Studio Sound Electronics are not affiliated with these companies.
All company names, logos and product names mentioned on these pages are trademarks of their respective owners.

Copyright ©2017 Studio Sound Electronics - All Rights Reserved
Not responsible for web site errors or omissions