
Click on photo for
larger view |
JACK, 1/4", MONO, OPEN CIRCUIT, WIRED, Switchcraft®
Found in many guitars, effects pedals, amps speaker output. Includes nut and washer.
Peavey part number 71466001.
Part #J-11 |
$2.25 |
|

Click on photo for
larger view |
JACK, 1/4", MONO, CLOSED CIRCUIT (SHORTING), WIRED, Switchcraft®
Found in vintage amps as the input jack. Includes nut and washer.
Peavey part number 71466004.
Part #J-12A |
$2.79 |
|

Click on photo for
larger view |
JACK, 1/4", MONO, CLOSED CIRCUIT
(SHORTING), WIRED, Switchcraft®, LONG BUSHING
Same as the J-12A jack, but with longer (3/8") threaded bushing for mounting in thicker panels. Includes nut and washer.
Part #J-L12A |
$2.99 |
|

Click on photo for
larger view |
JACK, 1/4", MONO,
TIP SHUNT, WIRED, Switchcraft®,
LONG BUSHING, ISOLATION WASHERS
Same as the Switchcraft L12A jack but
includes a set of isolation washers.
The
isolation washers keep the jack from making contact with your chassis. This
leaves the jack ungrounded which is needed in certain applications.
Commonly used in older Fender® Hot Rod Deluxe/Deville and Blues Deluxe/Deville
amps to
replace the fragile input jacks.
Part #J-L12AW |
$3.49 |
|

Click on photo for
larger view |
JACK, 1/4", TIP-RING-SLEEVE, OPEN CIRCUIT, WIRED, Switchcraft®
Used with T/R/S plugs for either balanced connections or stereo connections. Also very common in guitars with active pickups, and as the input jack on some effects pedals. The ring conductor is used in these cases to "turn on" the battery by tying one leg of the battery to ground via the plug.
Part #J-12B |
$2.99 |
|

Click on photo for
larger view |
JACK, 1/4", TIP-RING-SLEEVE, OPEN CIRCUIT, WIRED, Switchcraft®, LONG BUSHING
Same as the J-12B jack, but with longer (3/8") threaded bushing for mounting in thicker panels. Includes nut and washer.
Part #J-L12B |
$3.99 |
|

Click on photo for
larger view |
JACK, 1/4", TIP-SLEEVE, WITH TRANSFER SWITCHING. Switchcraft 13A Jack.
Used with for special switching applications - the tip contacts one terminal when no plug is inserted, and contacts a different terminal with
the plug in place.
Found in some Peavey amps, such as the Classic
50s speaker jack. Peavey part number 71466024.
Part #J-13A |
$6.99 |
|

Click on photo for
larger view |
JACK, 1/4", TIP/RING/SLEEVE, WITH
TIP SHUNT. Switchcraft 13B Jack.
Tip/Ring/Sleeve
Switchcraft jack. Tip has a shunt contact, ring contact is open
circuit.
Part #J-13B |
$6.95 |
|

Click on photo for
larger view |
JACK, 1/4", STEREO INPUT, CLOSED CIRCUIT, PC MOUNT, GENUINE CLIFF
UK
Stereo input jack. 6 PC board terminals, switched. With nut and washer.
Original Cliff UK part number CL1227.
Part #J-504 |
$2.29 |
|

Click on photo for
larger view |
SAVE WITH MULTIPACK! JACK, 1/4", STEREO INPUT, CLOSED CIRCUIT, PC MOUNT,
GENUINE CLIFF UK,
PACK OF 6
Stereo input jack. 6 PC board terminals, switched. Pack of 6 jacks, with nuts and washers.
Original Cliff UK part number CL1227.
Part #J-504-6 |
$10.99
(Set of 6 jacks) |
|

Click on photo for
larger view |
SAVE WITH
OUR
MULTIPACK ASSORTMENT! THIS PACK CONTAINS THREE J-503 (4 PIN) AND THREE J-504 (6-PIN)
JACKS.
Many amps contain both the 4 pin and the 6 pin Cliff jacks. This
assortment gives you 3 of each jack ... Three J-503, and three J-504.
Original Cliff UK part numbers CL1169 and CL1227.
Part # J-5034-6 |
$10.49
(For 3 J-503 Jacks and 3 J-504 Jacks)
|
|

Click on photo for
larger view |
JACK, 1/4",
T/R/S PC MOUNT PLASTIC, GENUINE CLIFF
UK, WITH EMI/RFI GROUND WASHER.
Same as the J-504, with the addition of a special ground washer which
contacts the chassis AND is inserted into the ground connection of the PC board
via dual pins under the jack. 6 PC board terminals for signal, plus
2 additional terminals for the ground washer. Only for
amplifiers so equipped for this jack, designed
to
reduced EMI/RFI interference (radio stations, ground loops). Found in some
Marshall solid state amps, as well as other brands. Note:
Must be used only on amps designed for this type of jack that have the PCB holes
to accept the pins of the ground washer. With nut and spacing washer.
Original Cliff UK part number CL1227/FCR14422.
Part #J-504GW |
$2.89 |
|

Click on photo for
larger view |
JACK, 1/4", STEREO INPUT, CLOSED CIRCUIT, PC MOUNT, GENUINE CLIFF - WHITE
Identical to the J-504 above, except in white. How cool is that! Stereo input jack. 6 PC board terminals, switched. With nut and washer.
Part #J-556 |
$3.99 |
|

Click on photo for
larger view |
JACK, 1/4", MONO PC MOUNT PLASTIC, GENUINE CLIFF
4 PC board terminals, switched. Used in many brands of amps and other equipment. With nut and washer.
Original Cliff UK part number CL1169.
Part #J-503 |
$1.99 |
|

Click on photo for
larger view |
SAVE WITH MULTIPACK! JACK, 1/4", MONO PC MOUNT PLASTIC,
GENUINE CLIFF UK,
PACK OF 6
4 PC board terminals, switched. Used in many brands of amps and other equipment.
Pack of 6 jacks, with nuts and washers. Original Cliff UK part number
CL1169.
Part #J-503-6 |
$9.99
(Set of 6 jacks) |
|

Click on photo for
larger view |
JACK,
1/4", MONO PC MOUNT PLASTIC, BRITISH STYLE WITH CHROME NUT AND CHROME TRIM RING
4 PC board terminals, switched. Used in many brands of amps and other
equipment. Same footprint as J-503 jack - may be used in place of
J-503 to add a touch of "chrome" class to your amp! Used in
newer Mesa Boogie amps, including the Rosette, Mini Rectifier, Mark
5:Twenty-Five, etc.
Part #J-603 |
$2.29
(per jack) |
|

Click on photo for
larger view |
JACK, 1/4", MONO PC MOUNT PLASTIC, GENUINE CLIFF
UK, WITH EMI/RFI GROUND WASHER.
Same as the J-503, with the addition of a special ground washer which
contacts the chassis AND is inserted into the ground connection of the PC board
via dual pins under the jack. 4 PC board terminals for signal, plus
2 additional terminals for the ground washer. Only for
amplifiers so equipped for this jack, designed
to
reduced EMI/RFI interference (radio stations, ground loops). Found in some
Marshall solid state amps, as well as other brands. Note:
Must be used only on amps designed for this type of jack that have the PCB holes
to accept the pins of the ground washer. With nut and spacing washer.
Original Cliff UK part number CL1169/FCR14422.
Part #J-503GW |
$2.59 |
|

Click on photo for
larger view |
JACK, 1/4", MONO INPUT, CLOSED CIRCUIT, PC MOUNT, GENUINE CLIFF - WHITE
Identical to the J-503 above, except in white. How cool is that! Mono input jack. 4 PC board terminals, switched. With nut and washer.
Part #J-555 |
$3.99 |
|

Click on photo for
larger view
|
JACK, 1/4", TIP/RING/SLEEVE 6-PIN, PC MOUNT,
Peavey® AMPS
Peavey® PCB mount 1/4" jack. Stereo, 6 pin. Fits certain
Peavey®
amp models. Peavey part number 71466323. Black nut is included. For savings on
multiple jacks, see J-518-6 below.
Part #J-518 |
$3.50 |
|

Click on photo for
larger view
|
SAVE WITH MULTIPACK! JACK, 1/4",
TIP/RING/SLEEVE 6-PIN, PC MOUNT,
Peavey® AMPS,
SET OF 6 JACKS.
Peavey® PCB mount 1/4" jack. Stereo, 6 pin. Fits certain
Peavey®
amp models. Peavey part number 71466323. Black nuts are included. Set of 6 jacks.
Part #J-518-6 |
$14.95
(For Set of 6 Jacks) |
|

Click on photo for
larger view
|
JACK, 1/4", MONO 4-PIN, PC MOUNT,
Peavey® AMPS
Peavey® PCB mount 1/4" jack.
Tip/Sleeve, 4 pin.
Fits certain Peavey®
amp models. Peavey part number 71466322. Black nut is
included. For savings on multiple jacks, see the J-519-6 jack set
below.
Part #J-519 |
$2.95 |
|

Click on photo for
larger view
|
SAVE WITH MULTIPACK! JACK, 1/4",
TIP/SLEEVE
4-PIN, PC MOUNT,
Peavey® AMPS,
SET OF 6 JACKS.
Peavey® PCB mount 1/4" jack.
Tip/sleeve, 4 pin.
Fits certain Peavey®
amp models. Peavey part number 71466322. Set of 6 jacks, black
nuts are included.
Part #J-519-6 |
$14.95 |
|
Click on photo for
larger view |
JACK, 1/4", MONO,
PC MOUNT, SHORT THREAD, PEAVEY
PCB mount 1/4" jack. Mono, 4 pin, PC board mount. Used in several
versions of the Peavey ValveKing amplifiers. Nut is included.
Part #J-661 |
$ 3.79
(per jack) |
|

Click on photo for
larger view |
JACK, 1/4",
STEREO,
PC MOUNT, SHORT THREAD, PEAVEY
PCB mount 1/4" jack. Mono, 6 pin, PC board mount. Used in several
versions of the Peavey ValveKing amplifiers. Nut is included.
Part #J-662 |
$ 3.99
(per jack) |
|

Click on photo for
larger view |
JACK NUT, PLASTIC,
GENUINE CLIFF UK, REPLACEMENT FOR Marshall® AND OTHERS.
Note: Replaces most black plastic jack nuts EXCEPT for
Roland. Will NOT fit Roland jacks.
Replacement jack nut as found on the J-502, J-503, J-504, J-505, J-503L and
J-504L jacks. Also fits the J-518 and J-519 jacks.
Part #J-5NT |
$0.50 |
|

Click on photo for
larger view |
JACK NUT MULTI-PACK - SAVE!
6 JACK NUTS, PLASTIC, GENUINE CLIFF UK, REPLACEMENT FOR Marshall® AND OTHERS.
Note: Replaces most black plastic jack nuts EXCEPT for
Roland. Will NOT fit Roland jacks.
Replacement jack nut as found on the J-502, J-503, J-504, J-505, J-503L and
J-504L jacks. Also fits the J-518 and J-519 jacks.
Part #J-5NT-6 |
$2.39 |
|

Click on photo for
larger view |
JACK NUT, PLASTIC,
GENUINE CLIFF UK, WHITE
Replacement nut for the J-555 and J-556 jacks.
Will also fit the J-502, J-503, J-504, J-505, J-503L, J-504L, J-518 and
J-519 black jacks, if you wish to create a two-tone effect.
Part #J-5NTW |
$0.60 |
|
Click on photo for
larger view |
JACK, 1/4", Peavey® PC MOUNT, STEREO, 5 PINS, SWITCHED, METAL BUSHING.
Both tip and
ring conductors are switched (normally closed). 5 pins. Original Peavey® part number 31466217. Used in Peavey®, Mackie and other brands.
Replaces Switchcraft 114BPCX and 114BPCSX. Nut and washer on this jack
ARE included.
Part #J-529 |
$2.75 |
|

Click on photo for
larger view
Note:
Nut & Washer NOT included - reuse original, or order JNUT-38. |
|
JACK, 1/4", PC MOUNT, STEREO,
4 PINS, SWITCHED, METAL BUSHING.
Tip is switched
(normally
closed), ring conductor is not switched. Used in a variety of brands.
Replaces Switchcraft.
NUT & WASHER NOT INCLUDED - REUSE ORIGINAL OR ORDER JNUT-38, BELOW.
Part #J-524A |
$3.50 |
|

Click on photo for
larger view
Note:
Nut & Washer NOT included - reuse original, or order JNUT-38. |
|
|
JACK, 1/4", PC MOUNT, STEREO, 5 PINS, SWITCHED, INSULATED.
Both tip and ring
conductors are switched (normally closed). Used in Peavey® and other brands. Same as J-529, except that the threads are insulated.
NUT & WASHER NOT INCLUDED - REUSE ORIGINAL OR ORDER JNUT-38, BELOW.
Part #J-523 |
$3.95 |
|

Click on photo for
larger view
Note: Nut
& Washer NOT included - reuse original, or order JNUT-38 |
|
JACK, 1/4", PC MOUNT, STEREO, 5 PINS, SWITCHED, INSULATED.
Both tip and ring conductors are switched (normally closed).
Used in Peavey® and other brands. Same as J-523, except that the pins are
smaller for insertion into smaller PC holes. Original Peavey part number
71466037. Switchcraft part number N114BPCSX.
NUT & WASHER NOT INCLUDED - REUSE ORIGINAL OR ORDER JNUT-38, BELOW.
Part #J-527 |
$4.50 |
|

Click on photo for
larger view
Note:
Nut & Washer NOT included - reuse original, or order JNUT-38 |
|
JACK, 1/4", Peavey® ORIGINAL,
DUAL TIP HID, PC MOUNT, MONO, 4 PINS.
SPECIAL APPLICATION!!
This jack is for special
applications in Peavey® products only, and is unusual in that two different pins contact the tip of the plug. One of the tip contacts is switched (normally closed),
and the other tip contact is open. This jack is exclusive to Peavey®.
NUT & WASHER NOT INCLUDED - REUSE ORIGINAL OR ORDER JNUT-38, BELOW.
Part #J-521 |
$2.95 |
|

Click on photo for
larger view
Note: Nut
& Washer NOT included - reuse original, or order JNUT-38 |
|
JACK, 1/4", Peavey® ORIGINAL,
DUAL TIP HID, PC MOUNT, MONO,
4 PINS, INSULATED.
SPECIAL APPLICATION!!
This jack is for special applications in Peavey® products only, and is unusual in that two different pins contact the tip of the plug. One of the tip contacts is switched (normally closed),
and the other tip contact is open. This jack is exclusive to Peavey®. Same as J-521 except that the threads are insulated.
NUT & WASHER NOT INCLUDED - REUSE ORIGINAL OR ORDER JNUT-38, BELOW.
Part #J-522 |
$2.95 |
|

Click on photo for
larger view
Note: Nut
& Washer NOT included - reuse original, or order JNUT-38 |
|
JACK, 1/4", PC MOUNT, STEREO,
3 PINS, NON-SWITCHED, METAL BUSHING.
Three conductors (tip, ring and sleeve), 3 pins. No switching.
Made by Neutrik/Rean. Replaces Switchcraft 112BPCX.
NUT & WASHER NOT INCLUDED - REUSE ORIGINAL OR ORDER JNUT-38, BELOW.
Part #J-234 |
$3.95 |
|

Click on photo for
larger view
Note: Nut
& Washer NOT included - reuse original, or order JNUT-38 |
|
JACK, 1/4", Used in Peavey®, PCB, MONO CLOSED CIRCUIT
PCB mono closed circuit. Original Peavey part numbers
71462088,
71466218, and
71466164.
NUT & WASHER NOT INCLUDED - REUSE ORIGINAL OR ORDER JNUT-38, BELOW.
Part #J-525 |
$4.99 |
|

Click on photo for
larger view
Note: Nut
& Washer NOT included - reuse original, or order JNUT-38 |
|
JACK, 1/4", PC MOUNT, STEREO, 5 PINS, SWITCHED, INSULATED. Made by Rean - used in many Peavey® models.
Original Peavey part number 71466165.
NUT & WASHER NOT INCLUDED - REUSE ORIGINAL OR ORDER JNUT-38, BELOW.
Part #J-526 |
$4.50 |
|

Click on photo for
larger view |
JACK, CHASSIS MOUNT, DIN, 6 PINS
This jack is commonly used as the footswitch connector on many Peavey® guitar amps. Also used by Genz Benz and other manufacturers. Original Peavey part number 71466018.
Part #J-520 |
$3.75 |
|

Click on photo for
larger view |
JACK, CHASSIS MOUNT, DIN, 7 PINS
This jack is commonly used as the footswitch connector on many Peavey® guitar amps. Also used by Mesa Boogie, Genz Benz and other manufacturers.
Part #J-516 |
$3.75 |
|

Click on photo for
larger view |
JACK, CHASSIS MOUNT, DIN, 8 PINS
This jack is commonly used as the footswitch connector on many Peavey® guitar amps. Also used by Genz Benz and other manufacturers.
Part #J-518 |
$3.75 |
|

Click on photo for
larger view |
SAVE WITH MULTIPACK!
JNUT-38 JACK NUT AND WASHER, METAL,
SWITCHCRAFT®, SET OF 6
Genuine Switchcraft® nut and washer set for the blackface/silverface Fender® bias pot, Mesa Boogie pots, and the
CTS or Alpha pots with 3/8" bushing (found on original vintage Fender®
blackface and silverface), as well as Peavey® and Switchcraft®
1/4" jacks. Does NOT fit the 24mm Marshall® pots. Set of
6 washers and 6 nuts.
Part #JNUT-38-6 |
$3.99
(Set of 6 washers and 6 nuts) |
|
 |
JACK NUT AND WASHER, METAL,
SWITCHCRAFT®
Genuine Switchcraft® nut and washer set for the blackface/silverface Fender® bias pot, Mesa Boogie pots, and the
CTS or Alpha pots with 3/8" bushing (found on original vintage Fender®
blackface and silverface), as well as Peavey® and Switchcraft®
1/4" jacks. Does NOT fit the 24mm Marshall® pots.
Part #JNUT-38 |
$0.89
(Set of 1 washer and 1 nut) |
|

Click on photo for
larger view. Jack is in the picture to demonstrate how the washers
are installed - jack is NOT included with the washers. |
INSULATING SHOULDER WASHER, FIBER
Pair of fiber insulating shoulder washers for Switchcraft jacks with metal
bushings. Used to mount standard jacks in a 1/2" diameter chassis
hole, while insulating the metal bushing (ground) of the jack from the chassis.
ID 3/8", OD 1/2". Works great when replacing isolated plastic jacks with a
more durable metal jack, which is frequently done on the input jacks of the
Fender® Hot Rod Deville/Deluxe and Blues Deville/Deluxe. Two washers
are used on each jack, and the "shoulders" are placed facing each other through
the chassis. The washers not only isolate the ground of the jack
electrically for noise reduction, but also stabilize the jack in the 1/2"
diameter hole. Jack shown in picture NOT included. Works
well with the Switchcraft J-11, J-L11, J-12A, J-L12A, J-12B, J-L12B, J-13,
J-13A, J-112APC, J-112BX, J-114BX, J-521 and J-524 jacks.
Part #ISW-3069 |
$0.49
(For a pair of washers. Each jack needs two washers.) |
|

Click on photo for
larger view |
JACK, 1/4", MONO, OPEN CIRCUIT, WIRED, Switchcraft®, LONG BUSHING,
ISOLATION WASHERS
Same as the Switchcraft L11 but includes fiber isolation washers. The isolation
washers keep the jack from making contact with your chassis. This leaves the
jack ungrounded which is needed in certain applications.
Part #J-L11W |
$3.49 |
|


Click on photo for
larger view |
Revisit™ SPEAKER HARNESS COMPLETE
WITH GENUINE SWITCHCRAFT #11 JACK and 24" SPEAKER WIRE FOR SINGLE SPEAKER.
Preassembled for speaker cabinets with one
speaker. Includes Switchcraft #11 jack,
and 24 inch Teflon™-insulated 18 ga speaker wire terminated in 3/16" push-on
speaker connectors. For two-speaker cabinets, see the SCH-2411X2,
below.
Part #SCH-2411 |
$8.99
|
|


Click on photo for
larger view |
Revisit™ SPEAKER HARNESS COMPLETE
WITH GENUINE SWITCHCRAFT #11 JACK and 24" SPEAKER WIRE FOR TWO SPEAKER
CABINET.
Preassembled for speaker cabinets with two
speakers in parallel. Includes Switchcraft #11 jack,
and 24 inch Teflon™-insulated 18 ga speaker wire terminated in 3/16" push-on
speaker connectors, plus an additional 24" jumper cable.
Part #SCH-2411X2 |
$14.99
|
|


Click on photo for
larger view |
Revisit™ SPEAKER HARNESS COMPLETE
WITH 1/4" STRAIGHT PLUG and 24" SPEAKER WIRE FOR SINGLE SPEAKER.
Preassembled for combo amps with one
speaker. Includes 1/4" straight plug,
and 24 inch Teflon™-insulated 18 ga speaker wire terminated in 3/16"
push-on speaker connectors. For 2-speaker cabinets, add the SJ-150 jumper,
below.
Part #SCH-224 |
$9.99
|
|


Click on photo for
larger view |
Revisit™
SPEAKER HARNESS, 2 ft LONG,
RIGHT-ANGLE PLUG TO BARE TINNED WIRE, 16 GAUGE CABLE
Replacement right-angle plug with 24" cable and stripped, tinned bare
wire.
Used to replace speaker cable in many combo amplifiers where the speakers are
connected to the amplifier chassis via a 1/4" jack and plug.
Heavy-duty 16ga round black speaker cable,
right-angle plug and bare wire ready for soldering to one
speaker.
Part #SCH-7090 |
$4.59 |
|


Click on photo for
larger view |
Revisit™
SPEAKER HARNESS, 2 ft LONG,
PUSH-ON TERMINALS, 16 GAUGE CABLE
Replacement right-angle plug with 24" cable and 3/16" fast-on connectors.
Used to replace speaker cable in many combo amplifiers where the speakers are
connected to the amplifier chassis via a 1/4" jack and plug.
Heavy-duty 16ga round black speaker cable,
right-angle plug and fast-on connectors for attachment to one
speaker.
Part #SCH-7080 |
$4.99 |
|


Click on photo for
larger view |
Revisit™
SPEAKER HARNESS
Replacement right-angle plug with 34" cable and 3/16" fast-on connectors.
Used to replace speaker cable in most combo amplifiers where the speakers are
connected to the amplifier chassis via a 1/4" jack and plug. 18ga black zip cord,
right-angle plug and fast-on connectors for attachment to one
speaker.
Part #SCH-280 |
$5.99 |
|


Click on photo for
larger view |
Revisit™
SPEAKER JUMPER CABLE
Teflon™ insulated silver plated copper speaker wire, 18 gauge, twisted pair,
black and white. Terminated at each end in standard 3/16" speaker
fast-on connectors. Great for connecting speakers in parallel in
2x12 or 4x12 cabinets. 24 inches (61 cm) long. Made in
USA.
Part #SJ-150 |
$5.99 |
|

Click on photo for
larger view |
JACK PLATE, BLACK METAL, SINGLE 1/4" JACK, 2" OUTSIDE DIAMETER. Similar in style to vintage Fender® jack plates. Works well with the Switchcraft J-11 1/4" jacks
that we carry. Hole is 3/8", for most Switchcraft type jacks. Easy to install, economical.
Jack not included - order separately. For size specifications, click here.
Part #JP-180 |
$1.39
|
|


Click on photo for
larger view |
Revisit™
JACK PLATE COMPLETE WITH
SWITCHCRAFT #11 JACK.
Switchcraft #11 jack preinstalled with lock washer and trim washer.
Outside diameter 2
inches (51mm). Designed to fit flush against a 1 1/8" (29mm) cabinet hole.
Easy to install - drill 1 1/8" hole in cabinet, attach speaker wiring to jack
and speaker, attach plate to cabinet.
Part #JPC-180 |
$4.95
|
|


Click on photo for
larger view |
Revisit™ JACK PLATE COMPLETE
WITH GENUINE SWITCHCRAFT #11 JACK and 24" SPEAKER WIRE.
Preassembled - includes 2" diameter single jack mounting plate with Switchcraft #11 jack preinstalled with lock washer and trim washer,
and 24 inch Teflon™-insulated 18 ga speaker wire terminated in 3/16" push-on
speaker connectors. Outside jack
plate diameter 2
inches (51mm). Designed to fit flush against a 1 1/8" (29mm) cabinet hole.
Easy to install - drill 1 1/8" hole in cabinet, attach speaker wiring to
speaker,
attach plate to cabinet. For two-speaker cabinets, see the JPH-182,
below.
Part #JPH-180 |
$11.95
|
|


Click on photo for
larger view |
Revisit™ JACK PLATE COMPLETE
WITH GENUINE SWITCHCRAFT #11 JACK and 24" SPEAKER WIRE, PLUS ADDITIONAL 24"
JUMPER.
Preassembled - includes 2" diameter single jack mounting plate with Switchcraft #11 jack preinstalled with lock washer and trim washer,
and 24 inch Teflon™-insulated 18 ga speaker wire terminated in 3/16" push-on
speaker connectors. Outside jack
plate diameter 2
inches (51mm). Designed to fit flush against a 1 1/8" (29mm) cabinet hole. Includes
a second 24 inch Teflon™-insulated 18 ga speaker wire terminated in 3/16"
push-on speaker connectors to connect to a second speaker in the same cabinet.
Easy to install - drill 1 1/8" hole in cabinet, attach speaker wiring to
speakers,
attach plate to cabinet.
Part #JPH-182 |
$15.95
|
|

Click on photo for
larger view |
Peavey binding post, pc mount, black.
Found on several models of Peavey power amplifiers. Red type also
available, below. Fits standard banana plugs.
Part #BP-277 |
$6.50 |
|

Click on photo for
larger view |
Peavey binding post, pc mount, red.
Found on several models of Peavey power amplifiers. Black type also
available, above. Fits standard banana plugs.
Part #BP-278 |
$6.50 |
|

Click on photo for
larger view |
JACK, SPEAKON, CHASSIS-MOUNT - MADE FOR PC BOARD (SOLDER PINS).
Made by Neutrik. 4 pins (1+, 1-, 2+, 2-) Used in a variety of brands, including
Peavey®.
Part #J-NL4MD-V |
$4.95 |
|

Click on photo for
larger view |
JACK, SPEAKON, CHASSIS-MOUNT - MADE FOR
WIRE ATTACHMENT (3/16" PUSH ON CONNECTORS OR SOLDER TABS).
Made by Neutrik. 4 pins (1+, 1-, 2+, 2-) Used in a variety of brands, including
Peavey®.
Part #J-NL4MP-2 |
$4.95 |
|
Strat®, Stratocaster®, Esquire®,
Telecaster®, Tele®, Jazzmaster®, Jaguar®, Mustang®, P.Bass®, J.Bass® and Fender®
are registered trademarks of Fender® Musical Instruments. The replacement necks
and bodies are for a Fender® or Squier® by Fender® guitar or bass. The
distinctive headstock designs and the distinctive body designs of the
Stratocaster®, Telecaster®, J.Bass®, P.Bass® and Tele® Bass are registered
trademarks of Fender® Musical Instruments Co.
Peavey® is a registered trademark of Peavey® Electronics Corporation.
Marshall® is a registered trademark of Marshall® Amplification Plc.
Mesa Boogie® is a registered trademark of MESA/Boogie® Ltd.
AmpRepairParts.com and Studio Sound Electronics are not affiliated with these companies.
All company names, logos and product names mentioned on these pages are trademarks of their respective owners.
Copyright ©2018 Studio Sound Electronics - All Rights Reserved
Not responsible for web site errors or omissions
|