|
|
Lamps |
|
|
Click on photo for
larger view |
NEW! BRIGHT LED INDICATOR LAMP,
REPLACES #47 BULB,
T-3-1/4, 6.3V, BAYONET BASE
Drop-in replacement long life LED replacement lamp for
pilot lamps. Fits Fender amps which are designed for the P-47 type
incandescent bulb (including most Fender amps from the 1950s through the
present). The LED
replacement is long lasting, runs much cooler, and is substantially brighter
than the P-47 incandescent bulb. If less brightness is desired,
install a series resistor feeding the lamp socket (1/4 or ½ watt, value
between 560Ω and 1KΩ). Sold individually. Add new pizzazz
to your amp with a brighter lamp on the front panel, and one which pays for
itself in the long run with exceptionally long life. Works on 6
volts, AC or DC.
Color is warm white. NOTE: NOT RECOMMENDED FOR USE WITH THE
PURPLE J-115P JEWEL - WILL RESULT IN A DEEP BLUE COLOR RATHER THAN PURPLE.
Part #LED-47 |
$2.95 |
|
Click on photo for
larger view |
NEW! COOL BLUE BRIGHT OUTPUT LED INDICATOR LAMP,
REPLACES #47 BULB,
T-3-1/4, 6.3V, BAYONET BASE
Drop-in replacement long life
BLUE OUTPUT LED replacement lamp for
pilot lamps. Fits Fender amps which are designed for the P-47 type
incandescent bulb (including most Fender amps from the 1950s through the
present). The LED replacement is long lasting, runs much cooler, and is substantially brighter than the P-47 incandescent bulb. Works on 6 volts, AC or DC. Output color is cool blue. When used with different colored jewels,
creates a different color and a different vibe! See the results below:
|
Jewel Color |
Resulting Look |
Brightness Level |
| JL-115A Amber |
Yellow |
High |
| JL-115B Blue |
Medium Blue |
High |
| JL-115C Clear |
Crystal Blue |
High |
| JL-115G Green |
Light Green |
High |
| JL-115P Purple |
Deep Blue |
Medium |
| JL-115Q Aqua |
Light to Med. Blue |
High |
| JL-115R Red |
Orange |
Medium |
| JL-115V Violet |
Bluish Violet |
Low |
| JL-115W White |
Baby Blue |
Low |
Part #LED-47B |
$2.95 |
|
Click on photo for
larger view |
INDICATOR LAMP, #47, T-3-1/4, 6.3V, .15 AMP, BAYONET BASE
P-47
General replacement lamps for dials, indicators, etc. Sold individually.
6.3V
Part #P-47 |
$0.99 |
|
Click on photo for
larger view |
BAD CAT AMPLIFIER LOGO ILLUMINATION LAMP SET. #259, 6V,
.25 AMP, WEDGE BASE
Long life general replacement lamps for
backlighting the Bad Cat logo on many models of Bad Cat amplifiers.
Set of 6 lamps.
Part #LP-259-6 |
$5.95
(for a set of 6 lamps) |
|
Click on photo for
larger view |
REPLACEMENT BULB FOR MORLEY™ EFFECTS AND VOLUME PEDALS
Long life replacement bulb used for both the pilot lamp and also to drive the photocell in all Morley pedals from 1983 through current models. Pedal not working? In most cases, it just needs a new bulb.
Part #L-387 |
$1.99 |
|
LED Colors Available:
Click on photo for
larger view |
5mm DIFFUSED LED - CHOICE OF COLORS
Standard 5mm (3/16") diameter diffused LED found in many guitar amplifiers
and effects pedals. Available in white, red, blue, green, or yellow. This 5mm size is commonly called the T-1-3/4
size. On LEDs the longer leg (the anode) goes to the
positive voltage supply. LEDs need a DC supply voltage and a resistor in series with them
to limit current. For a 9V supply, a 470 ohm resistor works well.
For 12 volts, a 680 ohm resistor, and for 15 volts, a 1K resistor.
Part #LED-5D |
$0.59
(per LED) |
|
LED Colors Available:
Click on photo for
larger view |
3mm DIFFUSED LED - CHOICE OF COLORS
Standard 3mm (1/8") diameter diffused LED found in many guitar amplifiers
and effects pedals. Available in white, red, blue, green, or yellow. This
3mm size is commonly called the T-1
size. On LEDs the longer leg (the anode) goes to the
positive voltage supply. LEDs need a DC supply voltage and a resistor in series with them
to limit current. For a 9V supply, a 470 ohm resistor works well.
For 12 volts, a 680 ohm resistor, and for 15 volts, a 1K resistor.
Part #LED-3D |
$0.39
(per LED) |
|
>
Click on photo for
larger view |
SUPER-BRIGHT 5mm RED WATERCLEAR LED
Standard 5mm (3/16") diameter waterclear red LED found in many guitar amplifiers
and effects pedals. A red waterclear LED looks clear when it is off,
and emits a bright red light when power is applied. On LED's the longer leg (the anode) goes to the
positive voltage supply. LED's need a DC supply voltage and a resistor in series with them
to limit current. For a 9V supply, a 470 ohm resistor works well.
For 12 volts, a 680 resistor resistor, and for 15 volts, a 1K resistor.
Part #LED-5R-WC |
$0.59 |
|
Click on photo for
larger view |
FENDER SQUARE 5mmX5mm DIFFUSED RED LED
Replaces the channel-switching indicator LED or the power
indicator in several Fender
amps and also in many Fender footswitches. Replaces original Fender
part number 028039. Found in Blues Deluxe, Blues Deville, Hot Rod Deluxe,
Hot Rod Deville, Deluxe 112, Deluxe 112 Plus, Ultimate Chorus, Princeton 112, Princeton 112 Plus,
Powerstage 100, Roc Pro 700, BXR200, KXR60, KXR100, KXR200, Frontman 25R, Pro
Reverb and Twin Amp (Pro Tube Series), Acoustasonic Jr.
Also found in the 028122 and 050419 Fender footswitches. This LED is
part of the circuitry in many Fender footswitches, and its failure often means
the channel switching stops functioning correctly. This LED is
red only - will not replace the bi-color footswitches used in some of these
amps.
Part #LED-573 |
$1.75 |
|
LED Colors Available:
Click on photo for
larger view |
BEZEL-MOUNTED LED WITH BUILT-IN
RESISTOR
The ultimate time saver! This is an LED mounted in a bezel with a
resistor and shrink wrapped wires.
Length is 19mm long - 16mm of which is below the mounting area. These Prewired LEDs are designed for 8V to 12V DC - no dropping resistor needed. The length
of the wire is about 6.5" Mounting hole is 8mm, LED color
choice is red, amber, green, blue or white.
Part #LED-725-X |
$1.95 |
|
Click on photo for
larger view |
PILOT LAMP HOLDER, REPLACEMENT FOR
FENDER™,
MESA BOOGIE™,
ORANGE™,
ETC.
Pilot lamp holder, fits 11/16" Chassis Hole
Bezel inner diameter: 0.570" Bezel inner diameter (including threading): 0.527" Works with a standard bayonet lamp such as the 6.3V #47 lamp,
or the LED-47. Accepts all of the colored jewels on this page.
Part #LH-124 |
$9.95 |
|
RED
Click on photo for
larger view |
PILOT LAMP ASSEMBLY, RED, REPLACEMENT FOR FENDER™
Complete pilot lamp assembly:
Includes pilot lamp holder,
red jewel and your choice of #47 bulb or equivalent LED-47. The LED option
provides a cooler, yet brighter light with much longer life. LED color is
`warm white`, for a color very close to that of a bulb. Fits 11/16" chassis hole.
Designed for 6 volts (filament voltage in tube amps). Ready for installation and wiring.
Available with 6V `warm white`
LED or standard 6V incandescent bulb - choose in "Options"
Part #FLA-124R |
$13.95 |
|
BLUE
Click on photo for
larger view |
PILOT LAMP ASSEMBLY, BLUE, REPLACEMENT FOR FENDER™
Complete pilot lamp assembly:
Includes pilot lamp holder,
blue jewel and your choice of #47 bulb or equivalent LED-47. The LED option
provides a cooler, yet brighter light with much longer life. LED color is
`warm white`, for a color very close to that of a bulb. Fits 11/16" chassis hole.
Designed for 6 volts (filament voltage in tube amps). Ready for installation and wiring.
Available with 6V `warm white`
LED or standard 6V incandescent bulb - choose in "Options"
Part #FLA-124B |
$13.95 |
|
AMBER
Click on photo for
larger view |
PILOT LAMP ASSEMBLY, AMBER, REPLACEMENT FOR FENDER™
Complete pilot lamp assembly:
Includes pilot lamp holder,
amber jewel and your choice of #47 bulb or equivalent LED-47. The LED option
provides a cooler, yet brighter light with much longer life. LED color is
`warm white`, for a color very close to that of a bulb. Fits 11/16" chassis hole.
Designed for 6 volts (filament voltage in tube amps). Ready for installation and wiring.
Available with 6V `warm white`
LED or standard 6V incandescent bulb - choose in "Options"
Part #FLA-124A |
$13.95 |
|
CLEAR
Click on photo for
larger view |
PILOT LAMP ASSEMBLY, CLEAR, REPLACEMENT FOR FENDER™
Complete pilot lamp assembly:
Includes pilot lamp holder,
clear jewel and your choice of #47 bulb or equivalent LED-47. The LED option
provides a cooler, yet brighter light with much longer life. LED color is
`warm white`, for a color very close to that of a bulb. Fits 11/16" chassis hole.
Designed for 6 volts (filament voltage in tube amps). Ready for installation and wiring.
Available with 6V `warm white`
LED or standard 6V incandescent bulb - choose in "Options"
Part #FLA-124C |
$13.95 |
|
GREEN
Click on photo for
larger view |
PILOT LAMP ASSEMBLY, GREEN, REPLACEMENT FOR FENDER™
Complete pilot lamp assembly:
Includes pilot lamp holder,
green jewel and your choice of #47 bulb or equivalent LED-47. The LED option
provides a cooler, yet brighter light with much longer life. LED color is
`warm white`, for a color very close to that of a bulb. Fits 11/16" chassis hole.
Designed for 6 volts (filament voltage in tube amps). Ready for installation and wiring.
Available with 6V `warm white`
LED or standard 6V incandescent bulb - choose in "Options"
Part #FLA-124G |
$13.95 |
|
VIOLET
Click on photo for
larger view |
PILOT LAMP ASSEMBLY, VIOLET, REPLACEMENT FOR FENDER™
Complete pilot lamp assembly:
Includes pilot lamp holder,
violet jewel and your choice of #47 bulb or equivalent LED-47. The LED option
provides a cooler, yet brighter light with much longer life. LED color is
`warm white`, for a color very close to that of a bulb. Fits 11/16" chassis hole.
Designed for 6 volts (filament voltage in tube amps). Ready for installation and wiring.
Available with 6V `warm white`
LED or standard 6V incandescent bulb - choose in "Options"
Part #FLA-124V |
$13.95 |
|
WHITE
Click on photo for
larger view |
PILOT LAMP ASSEMBLY, WHITE, REPLACEMENT FOR FENDER™
Complete pilot lamp assembly:
Includes pilot lamp holder,
white jewel and your choice of #47 bulb or equivalent LED-47. The LED option
provides a cooler, yet brighter light with much longer life. LED color is
`warm white`, for a color very close to that of a bulb. Fits 11/16" chassis hole.
Designed for 6 volts (filament voltage in tube amps). Ready for installation and wiring.
Available with 6V `warm white`
LED or standard 6V incandescent bulb - choose in "Options"
Part #FLA-124W |
$13.95 |
|
PURPLE
Click on photo for
larger view |
PILOT LAMP ASSEMBLY, PURPLE, REPLACEMENT FOR FENDER™
Complete pilot lamp assembly:
Includes pilot lamp holder,
purple jewel and #47 bulb complete, fits 11/16" chassis hole.
Designed for 6.3 volts. Ready for installation and wiring.
The purple color on this lamp jewel is toward the
cool end of the purple/violet range - so it has more of a bluish tint
to the purple color. In fact, the lamp jewel cover looks blue if the light
is not turned on. If you prefer a warmer tone (toward the red/pink end of
the scale), choose the FLA-124V violet lamp assembly. Not available with
the LED option, as the color when using an LED is a deep blue rather than
purple.
Part #FLA-124P |
$13.95 |
|
_small.png)
Click on photo for
larger view |
Marshall™ EARLY INDICATOR LIGHT
- 6 VOLT. NEW STYLE!
Square indicator light rated for 6.3 Volts.
Measures 0.4" length x 0.4" width x 0.12" depth. This style of square red
indicator light is similar to those found on many Marshall amps. The built
in mounting tabs eliminate the need for an additional mounting clip.Important! Twist the two leads around each other
before installation, and use only the minimum length necessary to reach a
source of 6V. This will minimize audio hum and interference.
Part #MPL-06
|
$11.95 |
|
Click on photo for
larger view |
Marshall™ VINTAGE INDICATOR LIGHT
- 120 VOLT.
Indicator light, square. 120 Volts. Measures: 0.47" Length x 0.47" Width x
0.09" Depth (3/8" mounting hole). Used
in vintage Marshall™ designs such as the JMP. 120 volt lamp -
designed to run off of the switched line voltage. Original
Marshall™ part. No retainer needed on this lamp - has automatic
lock-in to 3/8" mounting hole.
Part #MPL-120
|
$11.95 |
|
Click on photo for
larger view |
Marshall™ VINTAGE INDICATOR LIGHT
-
PURPLE, 6V LED.
Indicator light, square. Purple, LED powered,
for 6V only. As used in the Marshall Vintage Modern models 2266,
2466,
and 2266C. Original
Marshall™ part M-BULB-00007.
Part #MPL-007
|
$10.95 |
|
Click on photo for
larger view |
Marshall™ VINTAGE AMBER INDICATOR LIGHT
- 120 VOLT.
Indicator light, round. 120 Volts. 3/8" mounting hole. Used
in vintage Marshall™ designs such as the JTM-45 and JTM-100 from the early
1960s. Also found in other vintage British
amps. 120 volt lamp -
designed to run on the switched line voltage (North America only).
Mounting nut is included.
Part #MPL-6010
|
$12.95 |
|
Click on photo for
larger view |
Marshall™ VINTAGE RED INDICATOR LIGHT
- 120 VOLT.
Indicator light, round. 120 Volts. 3/8" mounting hole. Used
in vintage Marshall™ designs such as the JTM-45 and JTM-100 from the early
1960s. Also found in other vintage British
amps. 120 volt lamp -
designed to run on the switched line voltage (North America only).
Mounting nut is included.
Part #MPL-6010R
|
$12.95 |
|
.png)
WARNING: These products may contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.