|
|
Foot Switches |
|
|
|
Photo |
Description & Part No. |
Price |
Purchase |
Click on photo for
larger view |
FOOT SWITCH,
CARLING BRAND, SPDT
Found in many type of footswitches, including the earlier versions of the Dunlop Crybaby Wah pedals
(NOT the version F - see FS-435 below for Crybaby GCB-095F). Has 3 electrical terminals (single pole, double throw).
Solder lugs for wire.
Part #FS-492 |
$11.95 |
|
Click on photo for
larger view |
FOOT SWITCH,
CARLING BRAND, SPST, REPLACEMENT FOR Fender®, ETC.
Carling SPST footswitch. Used in Fender® etc. Reverb/tremolo/channel switching pedals.
Has 2 electrical terminals (single pole, single throw).
Solder lugs for wire.
Part #FS-493 |
$7.95 |
|
Click on photo for
larger view |
FOOT SWITCH,
CARLING BRAND, DPDT, FOR SWITCHING AND EFFECTS.
Has 6 electrical terminals (double pole, double throw).
Solder lugs for wire.
Part #FS-497 |
$13.95 |
|
Click on photo for
larger view |
FOOT SWITCH,
DPDT
Toe switch found in many type of footswitches, including the latest version
of the Dunlop Crybaby GCB-095F Wah Pedal. Has 6 electrical terminals (double pole, double throw).
Terminals can be used with the appropriate PC board, or with wire.
Original Dunlop Part number ECB-035.
Part #FS-435 |
$15.95
In Stock |
|
Click on photo for
larger view |
FOOT SWITCH,
DPDT, FOR SWITCHING AND EFFECTS.
Electrically equivalent to FS-497, but with a smaller switch body. Has 6 electrical terminals (double pole, double throw). Solder lugs for wire. Good quality, made in Taiwan.
Part #FS-498 |
$6.95 |
|
Click on photo for
larger view |
FOOT SWITCH,
DPDT, PC MOUNT, FOR SWITCHING AND EFFECTS.
Electrically equivalent and physically the same body size as the FS-498, but made for direct connection to a PC board. Found in the Line 6® XPS-AB power supply for their Variax guitars. Has 6 electrical terminals (double pole, double throw).
Good quality, made in Taiwan.
Part #FS-498-PC |
$6.95 |
|
Click on photo for
larger view |
FOOT SWITCH,
ALPHA MINIATURE DPDT, PC MOUNT, FOR SWITCHING AND EFFECTS.
Smaller body than the FS-498-PC, this switch is used in many stomp boxes and
in larger effects units such as the Line 6 FBV Shortboard. The
physical size of the pushbutton is the same as all of the other switches - only
the rectangular body of the switch is smaller for more compact spaces.
This is a "firm-click" switch - not a momentary.
Part #FS-211-PC |
$9.95 |
|
Click on photo for
larger view |
FOOT SWITCH,
ALPHA DPDT MOMENTARY, PC MOUNT, FOR SWITCHING AND EFFECTS.
This switch is the same as the FS-211-PC, except it is momentary (no firm
'click') for those pedals which require a momentary switch. Pins for PC
board mounting. The physical size of the pushbutton is the same as all of
the other switches - only the rectangular body of the switch is smaller for more
compact spaces.
Part #FS-211-M |
$9.95 |
|
Click on photo for
larger view |
FOOT SWITCH,
ALPHA DPDT, SOLDER
LUGS, FOR SWITCHING AND EFFECTS.
This switch is the same as the FS-211-PC, except it has solder lugs for wire
attachment. Made for effects boxes that do not have a PC board under
the footswitch. The physical size of the pushbutton is the same as all of
the other switches - only the rectangular body of the switch is smaller for more
compact spaces. This is a "firm-click" switch - not a momentary.
Part #FS-220 |
$9.95 |
|
Click on photo for
larger view |
FOOT SWITCH,
DPDT, MOMENTARY, FOR SWITCHING AND EFFECTS.
Made for switching and effects units which require a momentary connection rather than a "hard" connection (no "click"). Solder lugs for wire.
Good quality, made in Taiwan.
Part #FS-503 |
$7.95 |
|
Click on photo for
larger view |
FOOT SWITCH,
3PDT, SOLDER LUGS, FOR SWITCHING AND EFFECTS.
Has 9 electrical terminals (3 pole, double throw) Good quality, made in Taiwan. Commonly found in effects pedals which have "true bypass".
Solder lugs for wire.
Part #FS-501 |
$7.95 |
|
Click on photo for
larger view |
FOOT SWITCH,
3PDT, PC MOUNT, FOR SWITCHING AND EFFECTS.
Has 9 electrical terminals (3 pole, double throw) Good quality, made in Taiwan. Commonly found in effects pedals which have "true bypass".
Made for PC mounting. For simplification in using this switch to
modify your pedal to true bypass, see the PCB-200A below.
Part #FS-501-PC |
$8.95 |
|
Click on photo for
larger view
Click here for circuit wiring diagram |
TRUE BYPASS PC BOARD.
Designed to work with the FS-501-PC footswitch, above.
Greatly simplifies converting your pedal to true-bypass. PC board
solders directly to the 9 pins of the FS-501-PC, and wires then are connected
from the 8 terminals on the edge of the PC board to the board, input/output
jacks, LED, ground, etc. This board grounds the effects input in bypass
mode, which helps to reduce pops and noise. Adding this board to the
FS-501-PC and installing in your pedal will give it true bypass and the
capability for a effects on/off LED (even if it doesn't currently have an LED.
Note: Your pedal must currently have a hand-wired footswitch such as
the FS-435, FS-492, FS-497, FS-498. For best results, it should also
have hand-wired input and output jacks. Also, there must be
sufficient room to mount the FS-501-PC switch, which is a little larger than the
FS-435, FS-492, and FS-497 (it's about the same size as the FS-498).
If your existing footswitch is momentary or PC board mounted, this conversion
will not work on your pedal. Click
here for circuit wiring diagram.
Part #PCB-200A |
$1.99 |
|
Click on photo for
larger view |
FOOT SWITCH, REPLACEMENT FOR BOSS EFFECT PEDALS
Replacement for Boss effects pedals, SPST momentary, push switch. Mounts in square hole approximately .55" x .55" x 1.08" overall length including terminals.
Part #FS-511 |
$2.95 |
|
Click on photo for
larger view |
FOOTSWITCH, PC MOUNT, TACTILE TYPE
Common switch found in Line 6 floor pedals (such as the Pod XT Live), Digitech floor controllers (such as the Control ONE), and older DOD pedals. 12mm x 12mm (about 1/2" x 1/2" x 1/4" tall)
Part #FSM100 |
$1.95 |
|
Click on photo for
larger view |
9V BATTERY CLIP.
Commonly found in effects boxes.
Part #9VBC |
$0.45 |
|
|
Click on photo for
larger view |
FENDER STYLE FOOTSWITCH
Replacement for the original Fender two-button footswitch found on blackface
and silverface amps with vibrato and reverb. Sturdy chrome metal construction.
Dual RCA Plugs.
Part #FBS-271 |
$27.95 |
|
|
Click on photo for
larger view
|
MARSHALL STYLE FOOTSWITCH
Economical replacement for the original Marshall footswitch - same quality, just without the Marshall logo. Sturdy metal construction. Mono 1/4" Plug. Standard design - footswitch operation shorts the tip to the sleeve - will work with other makes and models of amplifiers as well as Marshall.
Part #FBS-470 |
$20.95 |
|
|
Click on photo for
larger view
|
MARSHALL STYLE FOOTSWITCH W/LED Economical replacement for the original Marshall footswitch - same quality, just without the Marshall logo. Sturdy metal construction. Fits the Marshall DSL100, DSL201 and DSL50, as well as other models. Mono 1/4" Plug. LED indicates condition of switch. Can be rewired internally to work with other amplifiers. Click here for wiring diagram.
Part #FBS-470L |
$21.95 |
|
|
Click on photo for
larger view
|
MARSHALL STYLE DUAL FOOTSWITCH
Economical replacement for the original Marshall footswitch - same quality, just without the Marshall logo. Sturdy metal construction. Standard design - operation of one of the footswitches shorts the tip to the sleeve, while the other switch shorts the ring to the sleeve. Can work with other makes and models of amplifiers as well as Marshall.
Part #FBS-471 |
$24.95 |
|
|
Click on photo for
larger view
|
MARSHALL STYLE DUAL FOOTSWITCH W/LED Economical replacement for the original Marshall footswitch - same quality, just without the Marshall logo. Sturdy metal construction. Fits the Marshall ValveState VS100R and VS100RH, and the DSL401 as well as other models. Stereo 1/4" Plug. LEDs indicate condition of switches. Can be rewired internally to work with other amplifiers. Click here for wiring diagram.
Part #FBS-471L |
$26.95 |
|
