Click on photo for
larger view |
F-CAP
This is the frequently lost Fender-logo plastic cap that
snaps onto the 1/4" right-angle speaker plug on vintage Blackface and
Silverface Fender™ amplifiers from the 1960s and 1970s. Exact fit
and replacement. For the plug, see the P-055 plug below.
Part #F-CAP |
$9.95 |
|
Click on photo for
larger view |
Fender™ Right-Angle Speaker Plug
Replacement Fender™ right-angle speaker plug
on vintage Blackface and Silverface Fender™ amplifiers from the 1960`s and
1970`s. Uses the F-CAP, above (not included - sold separately). Note: Requires a very hot soldering iron used
for minimal time when soldering to the case or center post of the plug.
Heat applied for an extended time will damage the plug.
Part #P-055 |
$11.99 |
|
|
Click on photo for
larger view
|
Fender™ Style RCA Plug from
Switchcraft
This is the original Switchcraft RCA plug used on vintage Fender
amps for footswitch and reverb in / out connections. For cable up to
0.125" (3.18mm) diameter.
Part #P-3501MX
|
$1.49
|
|
|
Click on photo for
larger view
|
Fender™
RCA VIBRATO SHORTING PLUG
by
Revisit™ - GOLD-PLATED. Did you know that on
vintage Fender™ amps (Blackface, Silverface), the reverb
will work without a footswitch plugged in, but the vibrato will not?
This handy-dandy little RCA shorting plug will fix that problem, if you do
not own or prefer not to use a footswitch on your vintage 60s or 70s Fender™
amp. This version is made of gold-plated brass for a low
resistance connection and highest immunity to oxidation. Just plug this little RCA plug gadget into the vibrato
footswitch jack on the back panel, and your vibrato will come alive.
Turn the intensity knob to zero to cut out the vibrato when this plug is
inserted. Note: Does not apply to Bronco, Vibro Champ, Princeton, or Princeton Reverb
amps. Inserting this plug turns the vibrato off in those models, removing
the plug turns it on.
Part #FSP-200
|
$2.50
|
|
Click on photo for
larger view |
PLUG, 1/4", MONO,
RIGHT ANGLE, SOLDER TERMINALS, STRAIN RELIEF
1/4" Mono 3-Conductor Right Angle Flat-Back Plug (Similar to
Switchcraft Type 228). Excellent quality construction - almost
indistinguishable from the 228.
Used for a variety of applications where Tip/Sleeve connections are needed
and space is at a premium. Frequently found on single Fender™ footswitch boxes. Includes Hardware.
Part #P-195 |
$4.29 |
|
Click on photo for
larger view |
PLUG, 1/4", STEREO,
RIGHT ANGLE, SOLDER TERMINALS, STRAIN RELIEF
1/4" Stereo 3-Conductor Right Angle Flat-Back Plug (Similar to
Switchcraft Type 238). Excellent quality construction - almost
indistinguishable from the 238.
Used for a variety of applications where Tip/Ring/Sleeve connections are needed
and space is at a premium. Frequently found on footswitch boxes -
particularly the footswitch box on the Fender™ Reissue `65 Twin and Deluxe Reverb
amps.
Includes Hardware.
Part #P-305 |
$4.99 |
|
Click on photo for
larger view |
 Revisit™
F1 to F2 Faston Push-on Terminal Adapters
Used to change the size of speaker terminals from .187" (3/16") to .250"
(1/4"). Also used to change some PC board connectors` size.
Female .187" to male .250"
Part #F1F2 |
$1.89
(Set of 2 Adapters) |
|
Click on photo for
larger view |
Revisit™
F2 to F1 Faston Push-on Terminal Adapters
Used to change the size of speaker terminals from .250" (1/4") to .187"
(3/16"). Also used to change some PC board connectors` size.
Female .250" to male .187"
Part #F2F1 |
$1.89
(Set of 2 Adapters) |
|
Click on photo for
larger view |
Revisit™
SPEAKER HARNESS
Replacement right-angle plug with 34" cable and 3/16" fast-on connectors.
Used to replace speaker cable in most combo amplifiers where the speakers are
connected to the amplifier chassis via a 1/4" jack and plug. 18ga black zip cord,
right-angle plug and fast-on connectors for attachment to one
speaker.
Part #SCH-280 - NOTE: OUT OF STOCK! NONE AVAILABLE AT THIS TIME. |
$6.99 |
 |
|
Click on photo for
larger view
|
SPEAKER JUMPER CABLE
polyvinyl
insulated silver plated copper speaker wire, 18 gauge, twisted
pair, black and white. Terminated at each end in standard
3/16" speaker fast-on connectors. Great for connecting
speakers in parallel in 2x12 or 4x12 cabinets. 24 inches (61
cm) long. Made in USA.
Part #SJ-150
|
$5.99
|
|
|
 |
BUILD YOUR OWN Speaker Harness for Combo Amps: Choose the SJ-150
cable (above) along with the P-287 Plug (below). Cut off the
cable's fast-on connectors on ONE end of the cable. Strip both
conductors of cable back about 1/4" on that end. Solder that end to
the P-287 plug (black to the sleeve, white to the tip.). This
will give you a 24 inch speaker harness. Note:
Cable-building experience strongly recommended. Soldering
equipment needed. |
Total cost for materials will be $5.99 + $3.95 = $9.94. |
 |
Click on photo for
larger view |
PLUG, 1/4", MONO, RIGHT ANGLE,
SOLDER TERMINALS, STRAIN RELIEF
Similar to the Switchcraft 226 right-angle plug. Nickel plated copper alloy.
2-conductor right-angle phone plug, solder terminals.
Part #P-287 |
$3.95 |
|
Click on photo for
larger view |
Revisit™ 18 GAUGE COPPER BONDED RED/BLACK ZIP CORD
Make low-cost, efficient speaker cables with this color-coded 18 gauge dual zip
cord. Red and black for easy polarity identification. Resistance
is 0.0097 ohms/ft.
Automotive grade "GPT" PVC insulation, oil and gas resistant, rated
for -20 deg F to +160 deg F. Also perfect
for bias testers, radio, home theatre, automotive, stereo, robotics, and model
train applications. Priced per foot, sold in lengths from 1 foot to
40 feet.
Part #RBZ-18 |
$0.32
(priced per foot) |
|
>
Click on photo for
larger view |
Revisit™ Fender™
STYLE "SPIDER" DISTRIBUTION CONNECTOR FOR BLACKFACE SPIDER SPEAKER HARNESSES
Replacement vintage style Spider distribution board, used to tie together
speaker wires in some vintage blackface Fender™ amps, particularly the vintage
blackface Super Reverb. Also found in some blackface 2-speaker amps,
including the
Pro Reverb, Twin Reverb, Vibrolux Reverb, and Vibroverb amplifiers from the 60s.
Part #FSJ-428 |
$6.50 |
|
Click on photo for
larger view |
 Fender™
STYLE SPEAKER CABINET JACK PLATE ASSEMBLY WITH JACK
As used on blackface and silverface speaker cabinet (Bassman, Bandmaster,
Showman, etc). Complete with long-bushing Switchcraft jack
with nut and trim washer, and two
nickel jack ferrules for the inside and outside of
the cabinet back. For wood panels between 3/8 inch and 1/2 inch thick.
Keep your vintage Fender™ cabinet looking original!
Part #JPC-577 |
$16.95 |
|
Click on photo for
larger view |
SPEAKER JUMPER CABLE
polyvinyl insulated silver plated copper speaker wire, 18 gauge, twisted pair,
black and white. Terminated at each end in standard 3/16" speaker
fast-on connectors. Great for connecting speakers in parallel in
2x12 or 4x12 cabinets. 24 inches (61 cm) long. Made in
USA.
Part #SJ-150 |
$5.99 |
|
WARNING: These products may contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.