1 foot long!


Click on photo for
larger view		 1 ft EXTENSION CORD, 3-WIRE, 16ga, 13 Amps.   Quality extension cord for use on stage, at home, office or workshop.  Cord length is 1 ft (including plug and socket), 16 gauge, 3-wire cord thickness is 0.31 inches (about 5/16" or 7.9mm).   Standard NEMA 5-15P plug and NEMA 5-15R single receptacle for North American use at 110-120 Volts AC, 13 amps maximum. Used only in North America.  Increases the ability of power strips to accept AC adaptors without blocking the adjacent outlet socket!   See inset photo for more info, click on it for a larger view.

Part #EC-5296		 $5.95
In stock


Click on photo for
larger view		 KNOB, Marshall™, SET-SCREW, SUB FOR UNAVAILABLE MARSHALL D-SHAFT KNOBS.  Used to replace D-Shaft pots used in the following Marshall™ amp models:   DSL-20HR Head, DSL-50 Head, DSL-100 Head, TSL-100 Head, TSL-60 Head, MA-50H Head, MA-100H Head, JVM-205C Combo, JVM-210C Combo, JVM-215C Combo, JVM-410C Combo, MHZ-15 Haze 15.   This substitute knob slips on the D-shaped shaft, and the set-screw is tightened against the round part of the shaft to hold the knob in place.   Looks like the original, and functions well.  
Part #MKDS-SUB		 $1.99
(Single Knob)
In stock


Click on photo for
larger view

 Revisit™ vintage Fender™ style reverb cable KIT for the original Fender™ 6G15 and the '63 Reverb Unit Reissue.   Set of parts for you to make two cables (reverb input and reverb output)   Both cables are 15 inches long, and they work great in the Fender stand-alone reverb units.  Open face braided shielded cable with metal RCA ends that you install - near-duplicate of the original O.E.M. Fender™ cables used in the 1960s.    Warning:  Not designed for use in amps other than Fender, due to the bare shields.  Soldering skills and tools required.
Part #RK-279R		 $11.95

Assembly required (with soldering skills needed)
In stock

  



Click on photo for
larger view		 Fender™ Electrolytic Filter Capacitor Kit 19A.  Used in the Super Twin (without Reverb) [180 Watts 1975-1976].  See the complete model cross reference. 

Contains the following capacitors, used as main filters, bias filter, and preamp cathode bypass capacitors:

  • 3 F&T 22uF-500V (Main Filters - Decoupling)
  • 2 F&T 220uF-300V (Main Filters)
  • 2 TAD 80uF-100V (Bias Filters)
  • 2 Axial 4.7uF-450V (Decoupling)
  • 2 Axial 25uF-25V (Cathode Bypass)
  • 1 Axial 4.7uF-50V (Cathode Bypass)
  • 1 Axial 680uF-6.3V (Cathode Bypass - Replaces 750uF-3V)
  • 1 Axial 150uF-6.3V (Cathode Bypass)

See the model cross reference for applicable models.  Download the installation guidelines.

Part #FCK-19A

 $69.95
In stock



Click on photo for
larger view		 Fender™ Electrolytic Filter Capacitor Kit 19B.  Used in the Super Twin Reverb [180 Watts 1975-1976].  See the complete model cross reference. 

Contains the following capacitors, used as main filters, bias filter, and preamp cathode bypass capacitors:

  • 3 F&T 22uF-500V (Main Filters - Decoupling)
  • 2 F&T 220uF-300V (Main Filters)
  • 2 TAD 80uF-100V (Bias Filters)
  • 2 Axial 4.7uF-450V (Decoupling)
  • 3 Axial 25uF-25V (Cathode Bypass)
  • 3 Axial 4.7uF-50V (Cathode Bypass)
  • 1 Axial 680uF-6.3V (Cathode Bypass - Replaces 750uF-3V)

See the model cross reference for applicable models.  Download the installation guidelines.

Part #FCK-19B

 $70.95
In stock



Click on photo for
larger view		 Fender™ Electrolytic Filter Capacitor Kit 46.  Used in the Fender Studio Bass Amp (200 watts)  See the complete model cross reference. 

Contains the following capacitors, used as main filters, bias filter, and preamp cathode bypass capacitors:

  • 3 F&T 22uF-500V (Main Filters - Decoupling)
  • 2 F&T 220uF-300V (Main Filters)
  • 2 TAD 80uF-100V (Bias Filters)
  • 2 Axial 25uF-25V (Cathode Bypass)
  • 1 Axial 4.7uF-50V (Cathode Bypass)
  • 1 Axial 680uF-6.3V (Cathode Bypass - Replaces 750uF-3V)
  • 1 Axial 150uF-6.3V (Cathode Bypass)
  • 1 2.2K-2W Resistor
  • 1 10K-2W Resistor

See the model cross reference for applicable models.  Download the installation guidelines.

Part #FCK-46

 $67.95
In stock


Click on photo for
larger view		 POT, 1 MEG LINEAR, 11mm, Marshall™ TYPE, PC MOUNT.  VALUE  B1M
Used for the Classic Gain, Classic Volume, and Ultra Volume in the Marshall™ DSL40CR and DSL100HR.    This pot has 4 pins.  Includes mounting nut.   11mm width, D-shaped shaft, 4 pins.

Part #P-VKG-B1M		 $6.95
In stock



Click on photo for
 larger view		 Revisit™ SPEAKER HARNESS
Replacement straight plug with 24" cable and bare stripped and tinned conductors for soldering to speaker terminals.   Used to replace the speaker cable in some combo amplifiers where the speakers are connected to the amplifier chassis via a 1/4" jack and plug.   Round black professional cable with black and white color-coded 18ga wires, straight metal 1/4 inch plug and bare tinned conductors for soldering to speaker terminals.
Part #SCH-7085		 $6.99
In stock


Click on photo for
larger view

BEHRINGER CABLE TESTER CT100
 Professional 6-in-1 Cable Tester

  • Built in a sturdy metal housing, this cable tester is indispensable for use on stage, at practice, and at home
  • Microprocessor-controlled cable tester featuring 3 modes: cable and installed cable test plus test tone mode
  • Accepts all standard connectors: XLR, TRS (1/4", 1/8", TT), RCA and MIDI
  • Super-easy operation with intuitive LED display
  • Continuity check and intermittent contact detection
  • Phantom-power and ground-shield check
  • Test-tone generator: 1 kHz or 440 Hz at +4 dBu, -10 dBV or -50 dBV
  • Belt clip included
  • Operates with 2 AA size batteries (not included)
  • High-quality components and exceptionally rugged construction ensure long life
  • Conceived and designed by BEHRINGER Germany

Make sure every cable in your arsenal is in good working order with the invaluable BEHRINGER Cable Tester CT100. This incredibly portable audio solution is a must-have for sound engineers and musicians alike.
Check out the video about this great cable tester here
Part #CT-100

 $31.95
In stock



Click on photo for larger view
Revisit™ Reverb Tank, 9" long, 2 spring, equivalent to Accutronics 2AB2A1B.  Lower cost short tank with 2 springs, Medium Decay, input impedance 10 ohms, output 2575 ohms, grounded input and grounded output. Mounts horizontal, open side down.   A replacement for some Mesa Boogie™ and Fender™ Models.    Also used in the PRS SE-20, Reverend Goblin, Kingsnake and early Hellhound models.  See explanation of reverb tank numbering system here.  See a chart which lists AC impedance and DC resistance measurements for reverb tanks here. 

Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet.

View the 2-year warranty details here.
Part #2AB2A1B

"Bringing back the sound of vintage USA-built Accutronics tanks"

 $29.95
In stock
 



Click on photo for larger view
Revisit™ Reverb Tank, 9" long, 2 spring, equivalent to Accutronics 2AB2A1C.  Lower cost short tank with 2 springs, Medium Decay, input impedance 10 ohms, output 2575 ohms, grounded input and grounded output. Mounts horizontal, open side down.   A replacement for some Mesa Boogie™ and Fender™ Models.    Also used in the PRS SE-20, Reverend Goblin, Kingsnake and early Hellhound models.  See explanation of reverb tank numbering system here.  See a chart which lists AC impedance and DC resistance measurements for reverb tanks here. 

Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet.

View the 2-year warranty details here.
Part #2AB2A1C

"Bringing back the sound of vintage USA-built Accutronics tanks"

 $29.95
In stock





Click on photo for larger view
Revisit™ Reverb Tank, 9" long, 2 spring, 2AB2C1A.   Lower cost short tank with Medium Decay, input impedance 10 ohms, output 2575 ohms, insulated input and grounded output. Mounts horizontal, open side up.   Replacement for tanks in early Yamaha solid-state amps from the 1970s and early 80s.  See explanation of reverb tank numbering system here.  See a chart which lists AC impedance and DC resistance measurements for reverb tanks here. 

Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet.

View the 2-year warranty details here.
Part #2AB2C1A

"Bringing back the sound of vintage USA-built Accutronics tanks"

 $29.95
In stock






Click on photo for larger view
Revisit™ Reverb Tank, 9" long, 2 spring, 2AB2C1B.   Lower cost short tank with 2 springs, Medium Decay, input impedance 10 ohms, output 2575 ohms, insulated input and grounded output. Mounts horizontal, open side down.   Found in Orange™ Rockerverb (HEAD ONLY), Orange™ Rockerverb MKII (HEAD ONLY), and Orange™ Rockerverb MKIII (HEAD ONLY).  See explanation of reverb tank numbering system here.  See a chart which lists AC impedance and DC resistance measurements for reverb tanks here. 

Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet.

View the 2-year warranty details here.
Part #2AB2C1B

"Bringing back the sound of vintage USA-built Accutronics tanks"

 $29.95
In stock




Click on photo for larger view
Revisit™ Reverb Tank, 9" long, 2 spring, 2AB2D1A.  Lower cost short tank with 2 springs, Medium Decay, input impedance 10 ohms, output 2575 ohms, isolated input and isolated output. Mounts horizontal, open side up.   May be used in some Roland™ JC120 (very early versions and also the JC120UT.   The 8DB2C1B is used in some other versions of the Jazz Chorus 120).   Unsure?   Measure input resistance on old tank - if it is less than 5 ohms, the 2AB2D1A is the replacement) Also used in the Roland™ Space Echo RE-501, RE-301, and RE-201.  as well as the Roland™ Bolt 60, and the Roland Jazz Chorus JC77.  See explanation of reverb tank numbering system here.  See a chart which lists AC impedance and DC resistance measurements for reverb tanks here. 
Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet.

View the 2-year warranty details here.
Part #2AB2D1A

"Bringing back the sound of vintage USA-built Accutronics tanks"

 $29.95
In stock







Click on photo for larger view
Revisit™ Reverb Tank, 9" long, 2 spring, 2AB2D1B.  Lower cost short tank with 2 springs, Medium Decay, input impedance 10 ohms, output 2575 ohms, isolated input and isolated output. Mounts horizontal, open side down.  Found in some versions of the Roland™ Space Echo RE-501 and RE-201 with the tank mounted on the bottom.  Also used in the Acoustic™ G60T (Model 162 or Model 163).  See explanation of reverb tank numbering system here.  See a chart which lists AC impedance and DC resistance measurements for reverb tanks here. 

Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet.

View the 2-year warranty details here.
Part #2AB2D1B

"Bringing back the sound of vintage USA-built Accutronics tanks"

 $29.95
In stock

 






Click on photo for larger view
Revisit™ Reverb Tank, 9" long, 2 spring, 2EB2C1B.   Lower cost short tank with 2 springs, Medium Decay, input impedance 800 ohms, output 2575 ohms, insulated input and grounded output. Mounts horizontal, open side down.   A quality tank at a budget price.  Replacement for Fender™ Blues Junior, Fender™ Transistor Amps such as:  Fender™ Deluxe 85, Fender™ Deluxe 90, Fender™ Princeton 65, Fender™ Stage Series, Fender™ Tube 60 Series (Super 60, Super 112), Fender™ Frontman 65R, Fender™ Eighty-Five, Fender™ Sidekick Reverb 35, Fender™ Sidekick Keyboard 60, Fender™ Ultra Chorus, Fender™ Ultimate Chorus, Fender™ Princeton Chorus, Fender™ H.O.T., Fender™ Vaporizer, Fender™ Acoustasonic Junior, Fender™ M-80 HM Series Combo, Peavey Envoy 110, Peavey™ Ultra 60/120, Peavey™ Backstage, Peavey™ Valveking series etc.,  Vox™ AC15CC, Vox™ AC15C, and Epiphone™ Valve Junior Hot Rod, Tech 21™ Trademark 30.  See explanation of reverb tank numbering system here.  See a chart which lists AC impedance and DC resistance measurements for reverb tanks here. 

Replaces Fender ™ part numbers 0028055000, 028055, 025269, 020550.
Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet.

View the 2-year warranty details here.
Part #2EB2C1B

"Bringing back the sound of vintage USA-built Accutronics tanks"

 $29.95
In stock

 






Click on photo for larger view
Revisit™ Reverb Tank, 9" long, 2 spring,  2EB2C1C.   Lower cost short tank with 2 springs, Medium Decay, input impedance 800 ohms, output 2575 ohms, insulated input and grounded output. Mounts on vertical wall, long axis horizontal, connectors up.  Used in the Burriss Royal Bluesman amp.  See explanation of reverb tank numbering system here.  See a chart which lists AC impedance and DC resistance measurements for reverb tanks here. 
Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet.

View the 2-year warranty details here.
Part #2EB2C1C

"Bringing back the sound of vintage USA-built Accutronics tanks"

 $29.95
In stock




Click on photo for larger view
Revisit™ Reverb Tank, 9" long, 2 spring, 2EB2C1D.  Lower cost short tank, Medium Decay, input impedance 800 ohms, output 2575 ohms, insulated input and grounded output. Mounts vertical wall, long axis horizontal, connectors down.   Used in Fender™ Acoustasonic Junior,  Fender™ M-80 HM Series Head, Tech 21™ Trademark 30.  See explanation of reverb tank numbering system here.  See a chart which lists AC impedance and DC resistance measurements for reverb tanks here. 

Replaces original Fender™ part number 0031669000.
Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet.

View the 2-year warranty details here.
Part #2EB2C1D

"Bringing back the sound of vintage USA-built Accutronics tanks"

 $29.95
In stock

 






Click on photo for larger view
Revisit™ Reverb Tank, 9" long, 2 spring, 2EB2C1E.   Lower cost short tank, Medium Decay, input impedance 800 ohms, output 2575 ohms, insulated input and grounded output.  Mounts on vertical wall with long axis vertical, input jack up.  Used  in Crate™ Tube Driver series of amps, such as the TD-70.  See explanation of reverb tank numbering system here.  See a chart which lists AC impedance and DC resistance measurements for reverb tanks here. 
Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet.

View the 2-year warranty details here.
Part #2EB2C1E

"Bringing back the sound of vintage USA-built Accutronics tanks"

 $29.95
In stock

 




Click on photo for
larger view		 JACK NUT/FERULE, BLACK PLASTIC, with BLACK PLASTIC BEZEL/WASHER - BRITISH CLIFF STYLE
Replacement nut and bezel washer for the J-501, J-501S, J-580, J-581, J-580L and J-581L jacks.   Note:   The threads on this nut are coarse (3/8-20), and are for genuine Cliff jacks.   Note:  There are some generic jacks on the market with finer thread nuts.   This nut will not fit those jacks.   This nut is for BRITISH CLIFF STYLE jacks.   Bezel is included with this nut.
 Part #JN-764W		 $1.15
In stock		  



Click on photo for
larger view		 Fender™ Electrolytic Filter Capacitor Kit 23A.  This kit includes a needed modification to improve the first stage filtering in the 65 Deluxe Reverb Reissue and the 68 Custom Deluxe Reverb, for which Fender admittedly had a poor design.   Installation of this kit results in a fuller sound with better low-end response, and is much closer to the design and tone of the original blackface and silverface Deluxe Reverb amps from the 1960s and early 1970s.

Contains the following capacitors, used as main filters, decoupling filters, bias filters, footswitch suppression, and cathode bypass capacitors in the Fender 65 Deluxe Reverb Reissue and the 68 Custom Deluxe Reverb amps, produced from 1993 to the present.   Complete instructions included.   Credit to Rob Robinette for this concept.

Top Professional Set:

2 TAD 70uF-350V Main Filters
3 TAD 22uF-500V Decoupling
7 TAD 25uF-25uF Bypass
1 TAD 5uF-50V Footswitch Filter
1 Radial 100uF-100V Bias Filter
1 Radial 22uF-63V Bias Filter
2 220K-1W Balancing Resistors

$53.95

Basic Economy Set:

2 MOD 70uF-350V Main Filters
3 MOD 20uF-500V Decoupling
7 MOD 25uF-50uF Bypass
1 I.C. 4.7uF-50V Footswitch Filter
1 Radial 100uF-100V Bias Filter
1 Radial 22uF-63V Bias Filter
2 220K-1W Balancing Resistors

$31.95

Part #FCK-23A

Top Professional Set:
$53.95 

Basic Economy
Set:
$31.95


In stock
Select Option:


Quantity:


Click on photo for
larger view		 FULL-SIZE TOGGLE SWITCH, CARLING™, DPST, SHORT BAT HANDLE

Carling, DPST 2 position toggle with solder lugs (3A, 125V). 6 Solder Lugs - 2 on each end, and 2 on the bottom (common lugs).   0.500 toggle length. On-Off (no center position).   When used as an AC power switch, opens both sides of the line.

 Part #SW-529		 $12.95
In stock		  


Click on photo for
larger view		 30K OHM 20 WATT RESISTOR, AXIAL.   Replaces either a 30K ohm or 33K ohm 20 watt resistor located near the power transformer in ultralinear Fender amplifiers.  Found in the Ultralinear versions of the Bandmaster Reverb, Bassman 70, Bassman 135, Dual Showman, Pro Reverb, Super Reverb, Twin Reverb and Fender Model 75 amps made from 1976 until 1982.
 Part #30K20W		 $2.95
In stock


Click on photo for
larger view		 150 OHM 7 WATT RESISTOR, AXIAL, PACK OF 2.   Replaces the 150 ohm cathode resistors connecting pin 8 of the 6L6 output tubes to ground in Fender amps made in 1968 and early 1969.  Found in the Bandmaster AC568, Bandmaster Reverb AA768, Bassman AC568, Dual Showman AC568 (has 4 resistors), Pro Reverb AB668, Showman AB568/AC568 (has 4 resistors), Showman Reverb AA768 (has 4 resistors), Super Reverb AB568, Twin Reverb AB568 (has 4 resistors), and Vibrolux Reverb AB568.  Inset photo shows typical original installation.
 Part #150R7WX2		 $2.50
(pack of 2 resistors)
In stock


Click on photo for
larger view

 Fender™ SINGLE FOOTSWITCH BOTTOM COVER
Fits original Fender™ single footswitch and Revisit™ single replacement footswitches FBS-270 and FBS-270B.  Made of flexible plastic - snaps onto the bottom of the footswitch housing.
Part #FSPB-270		 $5.95
In stock		  


Click on photo for
larger view

 Fender™ DUAL FOOTSWITCH BOTTOM COVER
Fits original Fender™ dual footswitch and Revisit™ dual replacement footswitches FBS-241, FBS-322, FBS-271 and FBS-271B.  Made of flexible plastic - snaps onto the bottom of the footswitch housing.
Part #FSPB-271		 $5.95
In stock


Click on photo for
larger view		 LARGE POWER ROCKER SWITCH, LIGHTED,  ENGL 
Used in the ENGL Founders Edition E670FE, Powerball E645, Fireball 100 E635, Poweramp 50/50 E840, Screamer 50 E335, and other models. Has 4 electrical terminals on back of switch.   1/4" push-on terminals.   Rated 16A.  For use on 125VAC or 250VAC.  15/16" x 1 1/16" x 1" deep.  Internal neon lamp.
Part #SW-493E
 $6.95
In stock		  


Click on photo for
larger view		 LARGE STANDBY ROCKER SWITCH,   ENGL 
Used in the ENGL Founders Edition E670FE, Powerball E645, Fireball 100 E635, Poweramp 50/50 E840, Screamer 50 E335, and other models. Has 4 electrical terminals on back of switch.   1/4" push-on terminals.   Rated 16A.  For use on 125VAC or 250VAC.  15/16" x 1 1/16" x 1" deep.  
 Part #SW-490E
 $6.95
In stock		  



Click on photo for
larger view		 TUBE SHIELD, REVISIT™, BAYONET "PUSH AND TWIST" TYPE, ALUMINUM, 2" TALL, SET OF 50.  Great for amp repair technicians!  Includes new bases, if needed.  Spring in top of shield fits over the tube.  Fits 12AX7A and similarly sized preamp tubes. Replacement for Fender™ and many other brands.  Holes in base spaced 1 1/8" apart.  Shield and base only - socket not included.  Made by Revisit™.   Set of 50 in handy divided box for space-saving storage!   Many Fender™ amps use 6 of these shields, so fifty is not too many to have on hand especially at this price of $1.10 per shield! Also found in some models of Ampeg™, Crate™, Vintage Marshall™, Mesa Boogie™, Orange™ and Peavey™ amps.   Top quality, RoHS compliant.
 Part #RS-325S-50		 $54.95
In stock		  

 

Click on photo for
larger view
 JACK, 1/4", Peavey™ ORIGINAL, DUAL TIP HID, PC MOUNT, MONO, 4 PINS (NARROW PINS).  SPECIAL APPLICATION!! 
 This jack is for use in Peavey™ products only, and is unusual in that two different pins contact the tip of the plug.  One of the tip contacts is switched (normally closed), and the other tip contact is open.  The pins on this jack are narrow (1.1mm).  For the same jack with wide pins, see the J-521.  This jack is exclusive to Peavey™.  Peavey part number 71466214 or 31466214. Used for a variety of functions on Peavey products, including input jacks.  Found in the Fire Bass 700, 5150II, 6505+, GPS1500, Classic 20, Classic 30, Delta Blues, 112TI, 115TI, Triple XXX, Van Halen 5150, PV2000, and some Ecoustic models, among others. Nut and washer included.
Part #J-214		 $8.95
In stock

 
Click on photo for
larger view		 JACK, 1/4", PC MOUNT, STEREO, 5 PINS, SWITCHED, METAL BUSHING.  
Both tip and ring conductors are switched (normally closed).  5 pins.    Original Peavey™ part number 31466217.  Found in most Peavey™ Vyper™ models as the input jack.  Also used in the Triple XXX, Classic 20, Classic 30, Delta Blues, 6505, XR600F, among other models.  Nut and washer included.
Part #J-217		 $4.95
In stock


Click on photo for
larger view		 SWITCH, TOGGLE, MESA BOOGIE, POWER AND STANDBY.    Two position (on/off), single pole (SPST).   Fits 1/2" chassis hole.  Quick connect terminals.  Found in the Mesa Boogie Badlander, Bass Prodigy, Bass Strategy, Dual Rectifier, Express Series, JP-2C, Lone Star, Lone Star Special, M6 & M9 Carbine, Mark I Reissue, Mark V, Mini Rectifier: 25, Rectifier Recording Preamp, Recto-Verb: 25, Road King, Roadster, Triple Crown, Triple Rectifier, WalkAbout.  Original Mesa Boogie part # 600631.
Part #SW-1018		 $16.95
In stock


Click on photo for
larger view		 SWITCH, TOGGLE, MESA BOOGIE, 3-POSITION POWER.    Three position (on/off/on), single pole (SPDT).   Fits 1/2" chassis hole.  Quick connect terminals.  Found in the Mesa Boogie Lone Star, Mark I Reissue, Mark V, and Roadster.   Switches between full power, off, and 'tweed' power.   Original Mesa Boogie part # 600639.
Part #SW-1019		 $19.95
In stock


Click on photo for
larger view		 33K OHM 20 WATT RESISTOR, RADIAL LEADS.   Found in some Fender amps made from 1976 until 1982.   Radial leads.
 Part #V33K20W		 $2.95
In stock		  

CAPACITOR, JJ ELECTRONIC, direct replacement for LCR type capacitors popular in Marshall™ and Vox™ series amps.    This is a dual can style capacitor 100uF/100uF rated at 500 volts.   Solder terminals for attaching wire leads.   1 3/8" diameter X 2 3/4" tall.  Very low ripple.    Made in the Slovak Republic in eastern Europe.  Founded in 1993 by Jan Jurco, JJ Electronic is a world-renowned manufacturer of vacuum tubes, electrolytic capacitors and high-end audio amplifiers.
 Part #JJ-100100		 $21.95
In stock		  


Click on photo for
larger view		 CAPACITOR, F&T/MERSEN BRAND, AXIAL LEAD ELECTROLYTIC, 25uF @ 70V.  Replacement for the 25uF/50V bias capacitors found in many Fender models from the early to mid 1960s.  Also can be used as an upgrade replacement for 25uF cathode bypass capacitors in vintage Fender amps.  Body of capacitor is 30mm X 14mm (1-1/8 inch X 1/2 inch).  Made in Germany.  Founded in 1948 by Heinz Fischer and Alfred Tausche, F&T Capacitors has over 75 years of experience in producing some of the finest capacitors available today. F&T Caps are known for their superior stability and reliability.
Part #FT-CAP-25-70		 $3.95
In stock		  


Click on photo for
larger view		 LOWER COST ROCKER SWITCH, LIGHTED POWER,  FOUND IN Marshall™ JVM, DSL, and JCM2000 SERIES.    This is a lower cost alternative switch (not Genuine Marshall) - this switch is manufactured by E-Switch, is of excellent quality, but has a MATTE finish rather than the original SHINY finish.  Used in the later versions of the TSL100, TSL122, DSL100, DSL50, DSL40, later versions of the DSL201 and DSL401, JVM210H, JVM410H, JVM215C, etc.     Also found in the DSL-5, DSL-15, and the Mode 4 MF-350.  Has 4 electrical terminals on back of switch.   1/4" push-on terminals.   Rated 16A.  For use on 125VAC or 250VAC.  15/16" x 1 1/16" x 1" deep.  Internal neon lamp. Replaces original Marshall part number 1310NB5NKR125V.
 Part #SW-493M
 $6.95
In stock		  


Click on photo for
larger view		 LOWER COST ROCKER SWITCH, STANDBY,  FOUND IN Marshall™ JVM, DSL, and JCM2000 SERIES.   This is a lower cost alternative switch (not Genuine Marshall) - this switch is manufactured by E-Switch, is of excellent quality, but has a MATTE finish rather than the original SHINY finish.  Used in the later versions of the TSL100, TSL122, DSL100, DSL50, DSL40, later versions of the DSL201 and DSL401, JVM210H, JVM410H, JVM215C, etc.     Also found in the DSL-5, DSL-15, and the Mode 4 MF-350.  Has 4 electrical terminals on back of switch.   1/4" push-on terminals.   Rated 16A.  For use on 125VAC or 250VAC.  15/16" x 1 1/16" x 1" deep.  Internal neon lamp. Genuine Marshall part number 1310NB5NKR125V.
 Part #SW-490M
 $6.95
In stock		  


Click on photo for
larger view		 ROCKER SWITCH, HI POWER/LOW POWER + STANDBY.  3 POSITION.  FOUND IN Marshall™ SC20C, SC20H, 2525H, 2525C, DSL100HR, DSL40CR, DSL20HR and DSL20CR.    Has 6 electrical terminals on back of switch.  MATTE FINISH (not shiny).  The shiny finish switch for this function is no longer available from Marshall.   1/4" push-on terminals.  Now in stock and ready to rock!  Rated 16A.   15/16" x 1 1/16" x 1" deep.   Only used in the SC20C, SC20H, 2525H, 2525C, DSL100HR, DSL40CR, DSL20HR and DSL20CR.
 Part #SW-496		 $9.95

In stock
 



Click on photo for
larger view		 TUBE SHIELD, REVISIT™, BAYONET "PUSH AND TWIST" TYPE, ALUMINUM, 2" TALL, SET OF 6.  Includes new bases, if needed.  Spring in top of shield fits over the tube.  Fits 12AX7A and similarly sized preamp tubes. Replacement for Fender™ and many other brands.  Holes in base spaced 1 1/8" apart.   This is a great kit to replaced all 6 of the tube shields in many Fender™ amps with 6 preamp tubes.  Shield and base only - socket not included.  Made by Revisit™.  Top quality, RoHS compliant.
 
 Part #RS-325S-6		 $8.95
In stock		  



Click on photo for
larger view		 TUBE SHIELD, REVISIT™, BAYONET "PUSH AND TWIST" TYPE, ALUMINUM, 2" TALL.  Includes new base, if needed.  Spring in top of shield fits over the tube.  Fits 12AX7A and similarly sized preamp tubes. Replacement for Fender™ and many other brands.  Holes in base spaced 1 1/8" apart.  Shield and base only - socket not included.  Made by Revisit™.  Top quality, RoHS compliant.
 
 Part #RS-325S		 $1.99
In stock		  

(Disregard color code in the picture.  The actual resistor is gray-red-brown-gold)

 RESISTOR, FLAMEPROOF, 820 OHM, 3 WATT.   Found in some versions of the Fender Blues and Hot Rod series amps as part of the power feed circuit to the footswitch.

 Part #820FP3		 $0.45 each
In stock		  

(Disregard color code in the picture.  The actual resistor is brown-red-red-gold)

 RESISTOR, FLAMEPROOF, 1.2K OHM, 3 WATT.   Found in some versions of the Fender Blues and Hot Rod series amps as part of the power feed circuit to the footswitch.

 Part #1200FP3		 $0.45 each
In stock		  

Click on photo for
larger view		 CAPACITOR, CERAMIC DISC, RADIAL.  Replacement for the ceramic disc 120pF "Bright Switch" capacitor in larger Fender Blackface and Silverface amps.  Capacitor is soldered to terminals on the Bright Switch on both channels.  Turning on the Bright Switch at lower volume allows more higher frequency tones through the amp circuitry, producing a brighter sound.
Part #C-CD-120PF		 $0.75
In stock		  


Click on photo for
larger view

JACK, 1/4", MONO 4-PIN, PC MOUNT, Fender™  Fender™ PCB mount 1/4" jack. Tip/Sleeve, 4 pin. Used as for all jacks on the Fender™ FM Frontman series amps.    Nut is included.   Original Fender™ part numbers 0062800000, 0062800049 and 0051658000.
Part #J-617

$3.50
In stock


Click on photo for
larger view		 WASHER, FOR BRITISH STYLE (CLIFF) JACKS.
This washer goes behind the faceplate on British style plastic nut and chrome nut jacks to provide proper spacing.   Jacks come with the washers included, but the washers are easily lost.  Without the washers, the jacks will not fit properly.  

Part #W-583		 $0.24
In stock


Click on photo for
larger view		 ROCKER SWITCH, POWER OR STANDBY, WHITE  Fits in rectangular cutout of 0.86" wide x 1.15" tall (22mm x 29mm).   Fits most any amp which uses a large rocker switch (Marshall, etc).  4 terminals push-on terminals on back of switch (switches both the hot and neutral sides.)  May be used for either Power or Standby.   Note - not illuminated.   This switch is priced to sell!
Part #SW-490CW		 $4.95
In stock


Click on photo for
larger view		 JACK, 1/4", CHROME NUT, CLOSED CIRCUIT, PC MOUNT, EXTENDED PCB PINS, TIP-SLEEVE, 4 PINS.   Usually found in amplifiers or pedals built in China or Taiwan.   Frequently used in Kustom™ products.  4 pins, PC mount, with chrome nut and washer.   Note "extended" pins as shown in photo. 
Part #J-580SL		 $3.95

 In stock




REVISIT™ DPDT PC MOUNT TOGGLE SWITCH w/LONG BAT HANDLE
Full size handle and bushing, miniature body.   PC mount.  Specifications: • Current rating: 5A @ 125 VAC, 2A @ 250 VAC • Contacts: 6 (DPDT - No center position) • Threaded bushing diameter: 12 mm (15/32") - fits in 1/2 inch hole.
Part #SW-236L		 $4.95
In stock




15 FEET

Click on photo for
 larger view		 Revisit™ INSTRUMENT CABLE 15 FEET
 Revisit 1/4" musical instrument cables provide the reliable link that lets you concentrate on a great performance. Also great for unbalanced line level interconnection, too.   15 feet long, 1/4" straight connectors.
  • 22 AWG oxygen-free copper stranded center conductor for maximum signal transfer
  • Coaxial construction and copper 95% braided shield reduce noise
  • Premium jacket materials provide ease of handling and long service life
  • Gold plated straight 1/4" connectors for long-term conductivity

    • Part #GCB-15

    		 $12.99
    In stock



    20 FEET

    Click on photo for
     larger view

    		 Revisit™ INSTRUMENT CABLE 20 FEET
         Revisit 1/4" musical instrument cables provide the reliable link that lets you concentrate on a great performance. Also great for unbalanced line level interconnection, too.   20 feet long, 1/4" straight connectors.
  • 22 AWG oxygen-free copper stranded center conductor for maximum signal transfer
  • Coaxial construction and copper 95% braided shield reduce noise
  • Premium jacket materials provide ease of handling and long service life
  • Gold plated straight 1/4" connectors for long-term conductivity

    • Part #GCB-20

    		 $13.99

    Only one is left in stock!



    20 FEET

    Click on photo for
     larger view

    		 Revisit™ INSTRUMENT CABLE RIGHT-ANGLE 20 FEET
         Revisit 1/4" musical instrument cables provide the reliable link that lets you concentrate on a great performance. Also great for unbalanced line level interconnection, too.   20 feet long, 1/4" straight and right-angle connectors.
    • 22 AWG oxygen-free copper stranded center conductor for maximum signal transfer
    • Made to handle all the abuse musicians can dish out
    • Coaxial construction and copper 95% braided shield reduce noise
    • Premium jacket materials provide ease of handling and long service life
    • Gold plated straight/right-angle 1/4" connectors for long-term conductivity
    • Durable metal shell for extra shielding and long service life
    Part #RGCB-20    		 $14.99 Available by June 10, 2025
    REVISIT    ™ CHANNEL SELECT TOGGLE SWITCH FOR Peavey™ (SHORT BAT-HANDLE, ORIGINAL)
    2P3TSP Toggle Switch used for the front panel channel select switch on the Triple XXX and Triple XXX II amp series.  Used as the resonance switch in the Ultra 112, Ultra 212, Ultra 410 combos and Ultra Plus head.  Replaces original Peavey™ part number 71322368 or 31322368.  
    Part #SW-236A    		 $4.95
    In stock


    Click on photo for
    larger view    		 SWITCH, STANDARD SIZE HEAVY-DUTY TOGGLE - Rated at 20 Amps (125VAC) or 10 Amps (250VAC).   Fits 1/2" chassis hole.  Screw terminals, or remove screws for soldered connections.  Single pole / single throw (SPST).   Two position - on/off.  
    Part #STS-8    		 $2.95
    In stock


    Click on photo for
    larger view    		 JACK, 1/4", CHROME NUT, CLOSED CIRCUIT, PC MOUNT, EXTENDED PCB PINS, TIP-RING-SLEEVE, 6 PINS.   Usually found in amplifiers or pedals built in China or Taiwan.   Frequently used in Kustom® products.  6 pins, PC mount, with chrome nut and washer.   Note "extended" pins as shown in photo.   For data sheet showing dimensions, click here
    Part #J-581SL    		 $3.95

     In stock
     


    Click on photo for
    larger view    		 JACK, 1/4", CHROME NUT, CLOSED CIRCUIT, PC MOUNT, EXTENDED PCB PINS, TIP-SLEEVE, 4 PINS.   Usually found in amplifiers or pedals built in China or Taiwan.   Frequently used in Kustom™ products.  4 pins, PC mount, with chrome nut and washer.   Note "extended" pins as shown in photo. 
    Part #J-580SL    		 $3.95

     In stock

    Adapter, RCA PLUG TO RCA  PLUG Allows connection of standard RCA cable to each other.  

    Part #P-282    		 $0.89

     In stock
     



    Click on photo for
    larger view    		 JACK, 1/4", PC MOUNT, STEREO, 3 PINS, SWITCHED, INSULATED.   Used in many Peavey™ and SWR™ models.  Switched tip contact.   Original Peavey™ part number 71466165.   Original SWR™ part number 0066442000.   Nut and washer are included.  3 pins.
    Part #J-526A    		 $7.75
    In stock    		  


    Click on photo for
     larger view
    		 Black Oxide Stainless Steel Pan Head 10-32 x 1" Speaker Mounting Screws, Rack Mount Screws
    Set of 4 screws.   Used to mount speakers, back panels, etc in a variety of amplifiers.    10-32 thread, 1" long with pan head.  May also be used as rack-mount screws.   Stainless steel, will not rust.
    Part #SC-202A    		 $1.79
    (for a set of 4 screws)
    In stock


    Click on photo for
    larger view    		 CAPACITOR, electrolytic 2200uF @ 63V with radial snap-in leads.  Made by Chemi-Con.  Dimensions:  22mm x 35mm.

     Part #RAD-2200-63    		 $6.95
    In stock    		  


     

    Click on photo for
    larger view

    		 Revisit™ BiasEasy™ 800
    The Bias Easy™ 800 measures the current in the power tubes of your amp. Includes two 8-pin probes with gold plated pins and socket, power adapter and  operating instructions.  Fully assembled and ready to use.  For 8-pin power tubes such as 6L6, 6V6, 5881, 6550, EL34, KT88, KT66, KT100, etc.   Not for 7591 tubes.

    The Bias Easy™ 800 allows you to monitor the bias setting safely and easily. While adjusting the bias control pot of your amp, the Bias Easy™ shows the actual current flowing through each of two power tubes.   A switch on the meter allows you to go back and forth between the two tubes.  This lets you set and evaluate the full reasonable biasing range your amp and tubes offer so that you may find the perfect setting.  Complete instructions are included.

    The bias setting has a dramatic impact on the amp's tone, response, break-up and dynamic character.
    Part #RBE-800

    $89.95
    In stock


     

    Click on photo for
    larger view

    		 Revisit™ BiasEasy™ 1200 Quad Tube Amp Bias Tester
    The Bias Easy™ 1200 measures the current in the power tubes of your amp.   Designed for amplifiers with 4 power tubes, such as 100 watt Marshalls and the Fender Twin Reverb.   (May also be used on amps with only 2 power tubes).   Includes four 8-pin probes with gold plated pins and socket, power adapter and  operating instructions.  Fully assembled and ready to use.  For 8-pin power tubes such as 6L6, 6V6, 5881, 6550, EL34, KT88, KT66, KT100, etc.   Not for 7591 tubes.

    The Bias Easy™ 1200 allows you to monitor the bias setting safely and easily. While adjusting the bias control pot of your amp, the Bias Easy™ 1200 shows the actual current flowing through each of the four power tubes.   A rotary switch on the meter allows you to check each tube for current flow.  This lets you set and evaluate the full reasonable biasing range your amp and tubes offer so that you may find the perfect setting.  Complete instructions are included.

    The bias setting has a dramatic impact on the amp's tone, response, break-up and dynamic character.
    Part #RBE-1200

    $124.95
    In stock


    Click on photo for
    larger view

    		 POTENTIOMETER WITH SWITCH, Used as the replacement for Fender part number 012561.   Distortion control in the Fender Super Twin and the Fender PS-300 (sometimes referred to as the 300-PS).   Has flattened D-shaft and rotary switch control.   The pot is a B100K.


     Part #012561

    		 $8.95
    In stock


    Click on photo for
    larger view    		 BALL HEAD MESH GRILLE AND WINDSCREEN FOR SHURE™
    Fits the majority of "58-style" microphones, including the Shure    ™ SM58, SM48, Beta 58A, SM58LC, SV100, RK143G, PGX2, Pyle™ PDMIC58, and virtually any other ball-style handheld microphone.   Save with this excellent Revisit™ reproduction at a fraction of the cost of the replacement Shure™ grille.
     Part #MG-58    		 $9.95
    In stock    		  


    Click on photo for
    larger view

    		 REVISIT POLARITY REVERSING ADAPTER CABLE
    Fixes the frustrating problem of having a power supply designed for "center pin positive" and a pedal which requires "center pin negative".  Or vice-versa!   This ingenious adapter cable reverses the center pin with the outside ring, allowing you to successfully use a "backwards" pedal with your pedal power supply.  The connectors are the popular 2.1mm x 5.5mm size.  5 inches long.
    Part #PRC-129    		 $2.29
    In stock    		  


    Click on photo for
    larger view    		 KNOB, Music Man™, SET-SCREW
    Music Man™ style amp knob, skirted with 1-10 numbering.  Traditional "Witches Hat" design.   For vintage Music Man™ amps.  With set-screw, for 1/4" smooth shaft pots.  These are different than the Fender skirted knobs.   A lot of people put Fender knobs on Music Man amps, but they won't exactly match the other knobs.   This is the exact replacement for Music Man.
    Part #K-155    		 $5.50
    In stock

    W-TAPER


    Click on photo for
    larger view    		 POT, W-TAPER, PC MOUNT, 16mm DIAMETER BODY, 7mm DIAMETER THREADED BUSHING, KNURLED SHAFT
    Found in many Hartke amps as well as other amps and pedals.  Typically used as an EQ pot.   W-Taper pots are reverse audio taper up to the midpoint, but regular audio taper past the midpoint.   Available with or without "center click detent" which marks the midpoint with a slight click you can feel as you turn the pot.  Diameter of the body of the pot is slightly smaller than a dime.  Available in the two most common values of W20K and W100K.   Both values are available with or without the center click detent.  Click on photo for more detail.    

         INCLUDES NUT & WASHER  (For spare or replacement nut, order the PNW-16 nut and washer set found here).
    Part #P-W16-XX    		 $3.95
    In stock

    Select Option 1:


    Select Option 2:


    Quantity:


    Click on photo for
    larger view    		 KNOB, Fender™ style "mini witch's hat", skirted 1-10, for KNURLED shaft pots.    Fender™ style amp knob, black, chrome center disc, skirted, with 1-10 numbering, knurled.  Knob is a slip-on, designed to fit a knurled shaft pot. Base is 7/8" diameter.   Fits any split knurled shaft pot, such as those found on certain models of the Sidekick series, the Rumble series etc.   Not for traditional Fender blackface, silverface models or the reissue versions of those amps.  For those, see the FVSK knobs.  Also not for other Fender models which have D-shaft pots, such as the Princeton 65, Super Champ series, etc.   See the K-328 for those models.
    Part #K-338    		 $1.95
    In stock


    Click on photo for
    larger view

    Fender™ RCA VIBRATO SHORTING PLUG by Revisit™ - GOLD-PLATED.   Did you know that on vintage Fender™ amps (Blackface, Silverface), the reverb will work without a footswitch plugged in, but the vibrato will not?   This handy-dandy little RCA shorting plug will fix that problem, if you do not own or prefer not to use a footswitch on your vintage 60s or 70s Fender™ amp.   This version is made of gold-plated brass for a low resistance connection and highest immunity to oxidation.  Just plug this little RCA plug gadget into the vibrato footswitch jack on the back panel, and your vibrato will come alive.    Turn the intensity knob to zero to cut out the vibrato when this plug is inserted.
    Part #FSP-200

    $2.50
    In stock

     


    Click on photo for
     larger view
    		 Black Oxide Stainless Steel Pan Head 4-40 x 5/16" Screws and Nuts, Set of 4
    Set of 4 small black screws with matching nuts.  Stainless steel with black oxide finish.  Used in a variety of applications on both guitars and amplifiers.
    Part #SCBN-440    		 $1.69
    (for a set of 4 screws with nuts)
    In stock




    Click on photo for
     larger view
    		 REVISIT™ 3-POSITION SLIDE SWITCH FOR Peavey™
    2P3T Slide Switch used for Impedance, Power Level, or Damping on the back panel of several Peavey™ amps.  Found in the Peavey Windsor Studio, 6505 112 Combo, Joe Satriani JSX, ValveKing 212 Combo, ValveKing Head, 5150-II, Supreme 160/Transtube Supreme and XXL models.  Replaces original Peavey™ part number 71322328 or 31322328.   Mounting hardware included
    Part #SW-313    		 $9.95
    In stock


    Click on photo for
    larger view    		 ROCKER SWITCH, MESA/BOOGIE, BASS 400+
         1/4" push-on terminals.   Made for 1.07" H x 0.88" W mounting hole.   Rated 20A @ 125VAC.   15A @ 250VAC.    Used for Power or Standby on the Bass 400+.  Original Mesa/Boogie part number 600505.

         Part #SW-547    		 $7.99
    In stock    		  


    Click on photo for
    larger view    		 FUSE HOLDER, HIGH QUALITY, USED ON VINTAGE Marshall™ AMPS  
    Marshall™ style fuse holder. Threaded mount for chassis hole diameters between 5/8" and 11/16".   Flush design, fuse cap removed with screwdriver.  Used on Marshalls from the 60's, 70's and 80`s, including the     JCM 800. This low profile fuse holder will make an excellent replacement for your original amplifier that is in need of repair or restoration. Easy to install and ready to serve you for years!  Fits 5mm X 20mm (GDC, GMA) size fuses.
    Part #FH-421    		 $9.95
    In stock    		  


    		 KNOB, Revisit™ Marshall™, PUSH ON D-SHAFT (Read applicable models!)

    Standard Revisit™ Marshall™ style control knob, push-on type, for D-Shaft pots used in the following Marshall™ amp models:   DSL-201 combo, DSL-401 combo, DSL-40C combo, TSL-122 combo, TSL-601 combo, TSL-602 combo, JVM205H head, JVM210H head, JVM410H head, VS15 combo, VS30R  combo, VS65R combo, VS100R combo, VS100RH head, VS102R combo, VS230 combo, VS265 combo, AVT20 combo, AVT50 combo, AVT50H head, AVT100 combo, AVT150 combo, AVT150H head, AVT275 combo, AS100D combo, MA50C Combo, MA100C Combo, MG10, MG15, MG15FX, MG30FX, MG50FX, MG100FX, MG100HFX, MG102FX.   For the similar knob used on DSL and TSL JCM2000 series heads, MA series heads, and JVM series combos see the MKDS knob elsewhere on this page.   The R-MKDS-C Knob is constructed so that the pointer on the front of the knob is 180 degrees away from the flat spot in the shaft hole on the back side of the knob.
    Part #R-MKDS-C

    		 $2.99
    (Single Knob)
    In stock


     

    Click on photo for
    larger view    		 JACK, 1/4", PC MOUNT, STEREO, 6 PINS, SWITCHED, INSULATED.    Original Peavey part number 31466165 and 71466165.  Found in some versions of the 5150, 6505, 5150-II and 6505+, as well as the pre-EQ jack on the KB60.  Used as the input jack on the older version of the Basic 112.  Nut and washer included.

         Part #J-625    		 $8.95
    In stock    		  

    Strat™, Stratocaster™, Esquire™, Telecaster™, Tele™, Jazzmaster™, Jaguar™, Mustang™, P.Bass™, J.Bass™ and Fender™ are registered trademarks of Fender™ Musical Instruments. The replacement necks and bodies are for a Fender™ or Squier™ by Fender™ guitar or bass. The distinctive headstock designs and the distinctive body designs of the Stratocaster™, Telecaster™, J.Bass™, P.Bass™ and Tele™ Bass are registered trademarks of Fender™ Musical Instruments Co.  
    Peavey™ is a registered trademark of Peavey™ Electronics Corporation.
    Marshall™ is a registered trademark of Marshall™ Amplification Plc.
    Mesa Boogie™ is a registered trademark of MESA/Boogie™ Ltd.
    AmpRepairParts.com and Studio Sound Electronics are not affiliated with these companies.
    All company names, logos and product names mentioned on these pages are trademarks of their respective owners.

    Copyright ©2025 Studio Sound Electronics - All Rights Reserved
    Not responsible for web site errors or omissions.
      WARNING: These products may contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
    For more information go to www.P65Warnings.ca.gov